Prev: PL2303 driver guide ?
Next: FT2232 JTAG
From: johannblake on 21 Dec 2005 03:36
I would like to build my own programmer for Microchip PICs. There are
many schematics on the Internet available but I can't seem to find
exactly what I want. What I would like is something that provides all
(or most) of the following functions:

* Can program PIC18 family of devices (or all of the major PIC families
if possible)

* In-circuit programming (not debugging): the electronics used for
programming need to be physically separated somehow from the
electronics of my own application circuit. However, if the number of
parts needed just for the programming section is relatively small, I
have no problem including these on my application board. The idea is
that I attach my application circuit to the programmer and program the
PIC. Then I remove my application circuit from the programmer and can
use my circuit immediately. This makes updating the firmware
convienient. I prefer not to have to remove PIC chips from sockets.

* The hardware needs to be supported by some well known software
application that will be used to flash the PICs.

* USB is the preferred interface between my PC and the programmer
although parallel and serial ports will also do.

* Would be nice to also have a schematic of a general purpose
development board containing LEDs, buttons, etc that are interfaced to
the PICs so that general breadboarding can be carried out. This
breadboard (development board) should also be separated from the actual
programming circuit. I realize that this is dependent on the actual PIC
type but if there is a schematic for prototyping PIC18 family (or
related PICs), that is what I could use.

Any partial suggestions are much appreciated.

Thanks again
Johann Blake

From: Stef Mientki on 21 Dec 2005 03:48
What about a bootloader ?
either through RS232 or USB,
works great.
Stef Mientki


johannblake(a)yahoo.com wrote:
> I would like to build my own programmer for Microchip PICs. There are
> many schematics on the Internet available but I can't seem to find
> exactly what I want. What I would like is something that provides all
> (or most) of the following functions:
>
> * Can program PIC18 family of devices (or all of the major PIC families
> if possible)
>
> * In-circuit programming (not debugging): the electronics used for
> programming need to be physically separated somehow from the
> electronics of my own application circuit. However, if the number of
> parts needed just for the programming section is relatively small, I
> have no problem including these on my application board. The idea is
> that I attach my application circuit to the programmer and program the
> PIC. Then I remove my application circuit from the programmer and can
> use my circuit immediately. This makes updating the firmware
> convienient. I prefer not to have to remove PIC chips from sockets.
>
> * The hardware needs to be supported by some well known software
> application that will be used to flash the PICs.
>
> * USB is the preferred interface between my PC and the programmer
> although parallel and serial ports will also do.
>
> * Would be nice to also have a schematic of a general purpose
> development board containing LEDs, buttons, etc that are interfaced to
> the PICs so that general breadboarding can be carried out. This
> breadboard (development board) should also be separated from the actual
> programming circuit. I realize that this is dependent on the actual PIC
> type but if there is a schematic for prototyping PIC18 family (or
> related PICs), that is what I could use.
>
> Any partial suggestions are much appreciated.
>
> Thanks again
> Johann Blake
>
From: johannblake on 21 Dec 2005 06:25
Stef, could you be a little more specific. What's a bootloader, what
hardware and software do you need to make it work?

Thanks
Johann

From: Donald on 21 Dec 2005 10:30
johannblake(a)yahoo.com wrote:
> Stef, could you be a little more specific. What's a bootloader, what
> hardware and software do you need to make it work?
>
> Thanks
> Johann
>
http://www.microchip.com/stellent/idcplg?IdcService=SS_GET_PAGE&nodeId=1824&appnote=en012031
From: David Tweed on 21 Dec 2005 17:40
johannblake(a)yahoo.com wrote:
> I would like to build my own programmer for Microchip PICs. There
> are many schematics on the Internet available but I can't seem to
> find exactly what I want. What I would like is something that
> provides all (or most) of the following functions:

Check out the EasyProg and QuickProto boards from Embed, Inc.:
http://www.embedinc.com/products/

Documentation for both is on-line, and you can buy the EasyProg
in kit form (or just a bare board).

-- Dave Tweed
 | 
Pages: 1
Prev: PL2303 driver guide ?
Next: FT2232 JTAG