Prev: [PATCH 3/3] Driver core: driver_attribute parameters can often be const*
Next: -tip: origin tree boot crash
From: Alberto Panizzo on 18 Dec 2009 10:50
The Epson LCD L4F00242T03 is mounted on the Freescale i.MX31 PDK
board.
Based upon Marek Vasut work in l4f00242t03.c, this driver provide
basilar init and power on/off functionality for this device.
Those functionality are accessible also through the /sys/class/lcd
interface.
Unfortunately Datasheet for this device are not available.
All the control sequences sent to the display were copied from the
peer freescale driver that leave in the i.MX31 Linux BSP.

The driver is tested to work as a module and build-in too.
As in the i.MX31PDK board the core and io suppliers are voltage
regulators, that functionality is embedded here, but not strict.

This patch apply to a 2.6.32-rc6 linus kernel.

Alberto!

Signed-off-by: Alberto Panizzo <maramaopercheseimorto(a)gmail.com>
---
drivers/video/backlight/Kconfig | 7 +
drivers/video/backlight/Makefile | 1 +
drivers/video/backlight/l4f00242t03.c | 244 +++++++++++++++++++++++++++++++++
include/linux/spi/l4f00242t03.h | 31 ++++
4 files changed, 283 insertions(+), 0 deletions(-)
create mode 100644 drivers/video/backlight/l4f00242t03.c
create mode 100644 include/linux/spi/l4f00242t03.h

diff --git a/drivers/video/backlight/Kconfig b/drivers/video/backlight/Kconfig
index 09bfa96..57ae4c0 100644
--- a/drivers/video/backlight/Kconfig
+++ b/drivers/video/backlight/Kconfig
@@ -31,6 +31,13 @@ config LCD_CORGI
Say y here to support the LCD panels usually found on SHARP
corgi (C7x0) and spitz (Cxx00) models.

+config LCD_L4F00242T03
+ tristate "Epson L4F00242T03 LCD"
+ depends on LCD_CLASS_DEVICE && SPI_MASTER && GENERIC_GPIO
+ help
+ SPI driver for Epson L4F00242T03. This provides basic support
+ for init and powering the LCD up/down through a sysfs interface.
+
config LCD_LMS283GF05
tristate "Samsung LMS283GF05 LCD"
depends on LCD_CLASS_DEVICE && SPI_MASTER && GENERIC_GPIO
diff --git a/drivers/video/backlight/Makefile b/drivers/video/backlight/Makefile
index 9a40554..e3e9e5f 100644
--- a/drivers/video/backlight/Makefile
+++ b/drivers/video/backlight/Makefile
@@ -3,6 +3,7 @@
obj-$(CONFIG_LCD_CLASS_DEVICE) += lcd.o
obj-$(CONFIG_LCD_CORGI) += corgi_lcd.o
obj-$(CONFIG_LCD_HP700) += jornada720_lcd.o
+obj-$(CONFIG_LCD_L4F00242T03) += l4f00242t03.o
obj-$(CONFIG_LCD_LMS283GF05) += lms283gf05.o
obj-$(CONFIG_LCD_LTV350QV) += ltv350qv.o
obj-$(CONFIG_LCD_ILI9320) += ili9320.o
diff --git a/drivers/video/backlight/l4f00242t03.c b/drivers/video/backlight/l4f00242t03.c
new file mode 100644
index 0000000..a0a020f
--- /dev/null
+++ b/drivers/video/backlight/l4f00242t03.c
@@ -0,0 +1,256 @@
+/*
+ * l4f00242t03.c -- support for Epson L4F00242T03 LCD
+ *
+ * Copyright 2007-2009 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * Copyright (c) 2009 Alberto Panizzo <maramaopercheseimorto(a)gmail.com>
+ * Inspired by Marek Vasut work in l4f00242t03.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/device.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/gpio.h>
+#include <linux/lcd.h>
+#include <linux/regulator/consumer.h>
+
+#include <linux/spi/spi.h>
+#include <linux/spi/l4f00242t03.h>
+
+struct l4f00242t03_priv {
+ struct spi_device *spi;
+ struct lcd_device *ld;
+ int lcd_on:1;
+ struct regulator *io_reg;
+ struct regulator *core_reg;
+};
+
+
+static void l4f00242t03_reset(unsigned int gpio)
+{
+ pr_debug("l4f00242t03_reset.\n");
+ gpio_set_value(gpio, 1);
+ mdelay(100);
+ gpio_set_value(gpio, 0);
+ mdelay(10); /* tRES >= 100us */
+ gpio_set_value(gpio, 1);
+ mdelay(20);
+}
+
+#define param(x) ((x) | 0x100)
+
+static void l4f00242t03_lcd_init(struct spi_device *spi)
+{
+ struct l4f00242t03_pdata *pdata = spi->dev.platform_data;
+ struct l4f00242t03_priv *priv = dev_get_drvdata(&spi->dev);
+ const u16 cmd[] = { 0x36, param(0), 0x3A, param(0x60) };
+
+ dev_dbg(&spi->dev, "initializing LCD\n");
+
+ if (priv->io_reg) {
+ regulator_set_voltage(priv->io_reg, 1800000, 1800000);
+ regulator_enable(priv->io_reg);
+ }
+
+ if (priv->core_reg) {
+ regulator_set_voltage(priv->core_reg, 2800000, 2800000);
+ regulator_enable(priv->core_reg);
+ }
+
+ gpio_set_value(pdata->data_enable_gpio, 1);
+ msleep(60);
+ spi_write(spi, (const u8 *)cmd, ARRAY_SIZE(cmd) * sizeof(u16));
+}
+
+static int l4f00242t03_lcd_power_set(struct lcd_device *ld, int power)
+{
+ struct l4f00242t03_priv *priv = lcd_get_data(ld);
+ struct spi_device *spi = priv->spi;
+
+ const u16 slpout = 0x11;
+ const u16 dison = 0x29;
+
+ const u16 slpin = 0x10;
+ const u16 disoff = 0x28;
+
+ if (power) {
+ if (priv->lcd_on)
+ return 0;
+
+ dev_dbg(&spi->dev, "turning on LCD\n");
+
+ spi_write(spi, (const u8 *)&slpout, sizeof(u16));
+ msleep(60);
+ spi_write(spi, (const u8 *)&dison, sizeof(u16));
+
+ priv->lcd_on = 1;
+ } else {
+ if (!priv->lcd_on)
+ return 0;
+
+ dev_dbg(&spi->dev, "turning off LCD\n");
+
+ spi_write(spi, (const u8 *)&disoff, sizeof(u16));
+ msleep(60);
+ spi_write(spi, (const u8 *)&slpin, sizeof(u16));
+
+ priv->lcd_on = 0;
+ }
+
+ return 0;
+}
+
+static struct lcd_ops l4f_ops = {
+ .set_power = l4f00242t03_lcd_power_set,
+ .get_power = NULL,
+};
+
+static int __devinit l4f00242t03_probe(struct spi_device *spi)
+{
+ struct l4f00242t03_priv *priv;
+ struct l4f00242t03_pdata *pdata = spi->dev.platform_data;
+ int ret;
+
+ if (pdata == NULL) {
+ dev_err(&spi->dev, "Uninitialized platform data.\n");
+ return -EINVAL;
+ }
+
+ priv = kzalloc(sizeof(struct l4f00242t03_priv), GFP_KERNEL);
+
+ if (priv == NULL) {
+ dev_err(&spi->dev, "No memory for this device.\n");
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ dev_set_drvdata(&spi->dev, priv);
+ spi->bits_per_word = 9;
+ spi_setup(spi);
+
+ priv->spi = spi;
+
+ ret = gpio_request(pdata->reset_gpio, "lcd l4f00242t03 reset");
+ if (ret) {
+ dev_err(&spi->dev,
+ "Unable to get the lcd l4f00242t03 reset gpio.\n");
+ return ret;
+ }
+
+ ret = gpio_direction_output(pdata->reset_gpio, 1);
+ if (ret)
+ goto err2;
+
+ ret = gpio_request(pdata->data_enable_gpio,
+ "lcd l4f00242t03 data enable");
+ if (ret) {
+ dev_err(&spi->dev,
+ "Unable to get the lcd l4f00242t03 data en gpio.\n");
+ return ret;
+ }
+
+ ret = gpio_direction_output(pdata->data_enable_gpio, 0);
+ if (ret)
+ goto err3;
+
+ if (pdata->io_supply) {
+ priv->io_reg = regulator_get(NULL, pdata->io_supply);
+
+ if (IS_ERR(priv->io_reg)) {
+ pr_err("%s: Unable to get the IO regulator\n",
+ __func__);
+ goto err3;
+ }
+ }
+
+ if (pdata->core_supply) {
+ priv->core_reg = regulator_get(NULL, pdata->core_supply);
+
+ if (IS_ERR(priv->core_reg)) {
+ pr_err("%s: Unable to get the core regulator\n",
+ __func__);
+ goto err4;
+ }
+ }
+
+ priv->ld = lcd_device_register("l4f00242t03",
+ &spi->dev, priv, &l4f_ops);
+ if (IS_ERR(priv->ld)) {
+ ret = PTR_ERR(priv->ld);
+ goto err5;
+ }
+
+ /* Init the LCD */
+ l4f00242t03_reset(pdata->reset_gpio);
+ l4f00242t03_lcd_init(spi);
+ l4f00242t03_lcd_power_set(priv->ld, 1);
+
+ dev_info(&spi->dev, "Epson l4f00242t03 lcd probed.\n");
+
+ return 0;
+
+err5:
+ if (priv->core_reg)
+ regulator_put(priv->core_reg);
+err4:
+ if (priv->io_reg)
+ regulator_put(priv->io_reg);
+err3:
+ gpio_free(pdata->data_enable_gpio);
+err2:
+ gpio_free(pdata->reset_gpio);
+err:
+ kfree(priv);
+
+ return ret;
+}
+
+static int __devexit l4f00242t03_remove(struct spi_device *spi)
+{
+ struct l4f00242t03_priv *priv = dev_get_drvdata(&spi->dev);
+ struct l4f00242t03_pdata *pdata = priv->spi->dev.platform_data;
+
+ l4f00242t03_lcd_power_set(priv->ld, 0);
+ lcd_device_unregister(priv->ld);
+
+ gpio_free(pdata->data_enable_gpio);
+ gpio_free(pdata->reset_gpio);
+
+ if (priv->io_reg)
+ regulator_put(priv->core_reg);
+ if (priv->core_reg)
+ regulator_put(priv->io_reg);
+
+ kfree(priv);
+
+ return 0;
+}
+
+static struct spi_driver l4f00242t03_driver = {
+ .driver = {
+ .name = "l4f00242t03",
+ .owner = THIS_MODULE,
+ },
+ .probe = l4f00242t03_probe,
+ .remove = __devexit_p(l4f00242t03_remove),
+};
+
+static __init int l4f00242t03_init(void)
+{
+ return spi_register_driver(&l4f00242t03_driver);
+}
+
+static __exit void l4f00242t03_exit(void)
+{
+ spi_unregister_driver(&l4f00242t03_driver);
+}
+
+module_init(l4f00242t03_init);
+module_exit(l4f00242t03_exit);
+
+MODULE_AUTHOR("Alberto Panizzo <maramaopercheseimorto(a)gmail.com>");
+MODULE_DESCRIPTION("EPSON L4F00242T03 LCD");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/spi/l4f00242t03.h b/include/linux/spi/l4f00242t03.h
new file mode 100644
index 0000000..3efb8e1
--- /dev/null
+++ b/include/linux/spi/l4f00242t03.h
@@ -0,0 +1,31 @@
+/*
+ * l4f00242t03.h -- Platform glue for Epson L4F00242T03 LCD
+ *
+ * Copyright (c) 2009 Alberto Panizzo <maramaopercheseimorto(a)gmail.com>
+ * Based on Marek Vasut work in lms283gf05.h
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+*/
+
+#ifndef _INCLUDE_LINUX_SPI_L4F00242T03_H_
+#define _INCLUDE_LINUX_SPI_L4F00242T03_H_
+
+struct l4f00242t03_pdata {
+ unsigned int reset_gpio;
+ unsigned int data_enable_gpio;
+ const char *io_supply; /* will be set to 1.8 V */
+ const char *core_supply; /* will be set to 2.8 V */
+};
+
+#endif /* _INCLUDE_LINUX_SPI_L4F00242T03_H_ */
--
1.6.3.3


--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo(a)vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
 | 
Pages: 1
Prev: [PATCH 3/3] Driver core: driver_attribute parameters can often be const*
Next: -tip: origin tree boot crash