[PATCH net-next] atl1e: Atheros L1E Gigabit Ethernet driver
in [Kernel]
|
Prev: bcm203x bluetooth dongle does not work
Next: What to do with `kswapd0: page allocation failure. ` ?
From: jie.yang on 17 Jul 2008 23:40 From: Jie Yang <jie.yang(a)atheros.com> Full patch for the Atheros L1E Gigabit Ethernet driver. Supportring AR8121, AR8113 and AR8114 Signed-off-by: Jie Yang <jie.yang @atheros.com> --- update on comments: 1) Remove dup MACRO already defined in linux/ethtool.h 2) Remove pci_using_64 logic for the reason as atl1 diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index 9490cb1..6223ceb 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -2314,6 +2314,17 @@ config ATL1 To compile this driver as a module, choose M here. The module will be called atl1. +config ATL1E + tristate "Atheros L1E Gigabit Ethernet support (EXPERIMENTAL)" + depends on PCI && EXPERIMENTAL + select CRC32 + select MII + help + This driver supports the Atheros L1E gigabit ethernet adapter. + + To compile this driver as a module, choose M here. The module + will be called atl1e. + endif # NETDEV_1000 # diff --git a/drivers/net/Makefile b/drivers/net/Makefile index 3292d0a..a7dc1ca 100644 --- a/drivers/net/Makefile +++ b/drivers/net/Makefile @@ -15,6 +15,7 @@ obj-$(CONFIG_EHEA) += ehea/ obj-$(CONFIG_CAN) += can/ obj-$(CONFIG_BONDING) += bonding/ obj-$(CONFIG_ATL1) += atlx/ +obj-$(CONFIG_ATL1E) += atl1e/ obj-$(CONFIG_GIANFAR) += gianfar_driver.o obj-$(CONFIG_TEHUTI) += tehuti.o diff --git a/drivers/net/atl1e/Makefile b/drivers/net/atl1e/Makefile new file mode 100644 index 0000000..bc11be8 --- /dev/null +++ b/drivers/net/atl1e/Makefile @@ -0,0 +1,2 @@ +obj-$(CONFIG_ATL1E) += atl1e.o +atl1e-objs += atl1e_main.o atl1e_hw.o atl1e_ethtool.o atl1e_param.o diff --git a/drivers/net/atl1e/atl1e.h b/drivers/net/atl1e/atl1e.h new file mode 100644 index 0000000..b645fa0 --- /dev/null +++ b/drivers/net/atl1e/atl1e.h @@ -0,0 +1,503 @@ +/* + * Copyright(c) 2007 Atheros Corporation. All rights reserved. + * Copyright(c) 2007 xiong huang <xiong.huang(a)atheros.com> + * + * Derived from Intel e1000 driver + * Copyright(c) 1999 - 2005 Intel Corporation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program; if not, write to the Free Software Foundation, Inc., 59 + * Temple Place - Suite 330, Boston, MA 02111-1307, USA. + */ + +#ifndef _ATL1E_H_ +#define _ATL1E_H_ + +#include <linux/version.h> +#include <linux/init.h> +#include <linux/types.h> +#include <linux/errno.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/netdevice.h> +#include <linux/etherdevice.h> +#include <linux/skbuff.h> +#include <linux/ioport.h> +#include <linux/slab.h> +#include <linux/list.h> +#include <linux/delay.h> +#include <linux/sched.h> +#include <linux/in.h> +#include <linux/ip.h> +#include <linux/ipv6.h> +#include <linux/udp.h> +#include <linux/mii.h> +#include <linux/io.h> +#include <linux/vmalloc.h> +#include <linux/pagemap.h> +#include <linux/tcp.h> +#include <linux/mii.h> +#include <linux/ethtool.h> +#include <linux/if_vlan.h> +#include <linux/workqueue.h> +#include <net/checksum.h> +#include <net/ip6_checksum.h> + +#include "atl1e_hw.h" + +#define PCI_REG_COMMAND 0x04 /* PCI Command Register */ +#define CMD_IO_SPACE 0x0001 +#define CMD_MEMORY_SPACE 0x0002 +#define CMD_BUS_MASTER 0x0004 + +#define BAR_0 0 +#define BAR_1 1 +#define BAR_5 5 + +/* Wake Up Filter Control */ +#define AT_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable */ +#define AT_WUFC_MAG 0x00000002 /* Magic Packet Wakeup Enable */ +#define AT_WUFC_EX 0x00000004 /* Directed Exact Wakeup Enable */ +#define AT_WUFC_MC 0x00000008 /* Multicast Wakeup Enable */ +#define AT_WUFC_BC 0x00000010 /* Broadcast Wakeup Enable */ + +#define SPEED_0 0xffff +#define HALF_DUPLEX 1 +#define FULL_DUPLEX 2 + +/* Error Codes */ +#define AT_ERR_EEPROM 1 +#define AT_ERR_PHY 2 +#define AT_ERR_CONFIG 3 +#define AT_ERR_PARAM 4 +#define AT_ERR_MAC_TYPE 5 +#define AT_ERR_PHY_TYPE 6 +#define AT_ERR_PHY_SPEED 7 +#define AT_ERR_PHY_RES 8 +#define AT_ERR_TIMEOUT 9 + +#define MAX_JUMBO_FRAME_SIZE 0x2000 + +#define AT_VLAN_TAG_TO_TPD_TAG(_vlan, _tpd) \ + _tpd = (((_vlan) << (4)) | (((_vlan) >> 13) & 7) |\ + (((_vlan) >> 9) & 8)) + +#define AT_TPD_TAG_TO_VLAN_TAG(_tpd, _vlan) \ + _vlan = (((_tpd) >> 8) | (((_tpd) & 0x77) << 9) |\ + (((_tdp) & 0x88) << 5)) + +#define AT_MAX_RECEIVE_QUEUE 4 +#define AT_PAGE_NUM_PER_QUEUE 2 + +#define AT_DMA_HI_ADDR_MASK 0xffffffff00000000ULL +#define AT_DMA_LO_ADDR_MASK 0x00000000ffffffffULL + +#define AT_TX_WATCHDOG (5 * HZ) +#define AT_MAX_INT_WORK 10 +#define AT_TWSI_EEPROM_TIMEOUT 100 +#define AT_HW_MAX_IDLE_DELAY 10 +#define AT_SUSPEND_LINK_TIMEOUT 28 + +#define AT_REGS_LEN 75 +#define AT_EEPROM_LEN 512 +#define AT_ADV_MASK (ADVERTISE_10_HALF |\ + ADVERTISE_10_FULL |\ + ADVERTISE_100_HALF |\ + ADVERTISE_100_FULL |\ + ADVERTISE_1000_FULL) + +/* tpd word 2 */ +#define TPD_BUFLEN_MASK 0x3FFF +#define TPD_BUFLEN_SHIFT 0 +#define TPD_DMAINT_MASK 0x0001 +#define TPD_DMAINT_SHIFT 14 +#define TPD_PKTNT_MASK 0x0001 +#define TPD_PKTINT_SHIFT 15 +#define TPD_VLANTAG_MASK 0xFFFF +#define TPD_VLAN_SHIFT 16 + +/* tpd word 3 bits 0:4 */ +#define TPD_EOP_MASK 0x0001 +#define TPD_EOP_SHIFT 0 +#define TPD_IP_VERSION_MASK 0x0001 +#define TPD_IP_VERSION_SHIFT 1 /* 0 : IPV4, 1 : IPV6 */ +#define TPD_INS_VL_TAG_MASK 0x0001 +#define TPD_INS_VL_TAG_SHIFT 2 +#define TPD_CC_SEGMENT_EN_MASK 0x0001 +#define TPD_CC_SEGMENT_EN_SHIFT 3 +#define TPD_SEGMENT_EN_MASK 0x0001 +#define TPD_SEGMENT_EN_SHIFT 4 + +/* tdp word 3 bits 5:7 if ip version is 0 */ +#define TPD_IP_CSUM_MASK 0x0001 +#define TPD_IP_CSUM_SHIFT 5 +#define TPD_TCP_CSUM_MASK 0x0001 +#define TPD_TCP_CSUM_SHIFT 6 +#define TPD_UDP_CSUM_MASK 0x0001 +#define TPD_UDP_CSUM_SHIFT 7 + +/* tdp word 3 bits 5:7 if ip version is 1 */ +#define TPD_V6_IPHLLO_MASK 0x0007 +#define TPD_V6_IPHLLO_SHIFT 7 + +/* tpd word 3 bits 8:9 bit */ +#define TPD_VL_TAGGED_MASK 0x0001 +#define TPD_VL_TAGGED_SHIFT 8 +#define TPD_ETHTYPE_MASK 0x0001 +#define TPD_ETHTYPE_SHIFT 9 + +/* tdp word 3 bits 10:13 if ip version is 0 */ +#define TDP_V4_IPHL_MASK 0x000F +#define TPD_V4_IPHL_SHIFT 10 + +/* tdp word 3 bits 10:13 if ip version is 1 */ +#define TPD_V6_IPHLHI_MASK 0x000F +#define TPD_V6_IPHLHI_SHIFT 10 + +/* tpd word 3 bit 14:31 if segment enabled */ +#define TPD_TCPHDRLEN_MASK 0x000F +#define TPD_TCPHDRLEN_SHIFT 14 +#define TPD_HDRFLAG_MASK 0x0001 +#define TPD_HDRFLAG_SHIFT 18 +#define TPD_MSS_MASK 0x1FFF +#define TPD_MSS_SHIFT 19 + +/* tdp word 3 bit 16:31 if custom csum enabled */ +#define TPD_PLOADOFFSET_MASK 0x00FF +#define TPD_PLOADOFFSET_SHIFT 16 +#define TPD_CCSUMOFFSET_MASK 0x00FF +#define TPD_CCSUMOFFSET_SHIFT 24 + +struct atl1e_tpd_desc { + __le64 buffer_addr; + __le32 word2; + __le32 word3; +}; + +/* how about 0x2000 */ +#define MAX_TX_BUF_LEN 0x2000 +#define MAX_TX_BUF_SHIFT 13 +/*#define MAX_TX_BUF_LEN 0x3000 */ + +/* rrs word 1 bit 0:31 */ +#define RRS_RX_CSUM_MASK 0xFFFF +#define RRS_RX_CSUM_SHIFT 0 +#define RRS_PKT_SIZE_MASK 0x3FFF +#define RRS_PKT_SIZE_SHIFT 16 +#define RRS_CPU_NUM_MASK 0x0003 +#define RRS_CPU_NUM_SHIFT 30 + +#define RRS_IS_RSS_IPV4 0x0001 +#define RRS_IS_RSS_IPV4_TCP 0x0002 +#define RRS_IS_RSS_IPV6 0x0004 +#define RRS_IS_RSS_IPV6_TCP 0x0008 +#define RRS_IS_IPV6 0x0010 +#define RRS_IS_IP_FRAG 0x0020 +#define RRS_IS_IP_DF 0x0040 +#define RRS_IS_802_3 0x0080 +#define RRS_IS_VLAN_TAG 0x0100 +#define RRS_IS_ERR_FRAME 0x0200 +#define RRS_IS_IPV4 0x0400 +#define RRS_IS_UDP 0x0800 +#define RRS_IS_TCP 0x1000 +#define RRS_IS_BCAST 0x2000 +#define RRS_IS_MCAST 0x4000 +#define RRS_IS_PAUSE 0x8000 + +#define RRS_ERR_BAD_CRC 0x0001 +#define RRS_ERR_CODE 0x0002 +#define RRS_ERR_DRIBBLE 0x0004 +#define RRS_ERR_RUNT 0x0008 +#define RRS_ERR_RX_OVERFLOW 0x0010 +#define RRS_ERR_TRUNC 0x0020 +#define RRS_ERR_IP_CSUM 0x0040 +#define RRS_ERR_L4_CSUM 0x0080 +#define RRS_ERR_LENGTH 0x0100 +#define RRS_ERR_DES_ADDR 0x0200 + +struct atl1e_recv_ret_status { + u16 seq_num; + u16 hash_lo; + __le32 word1; + u16 pkt_flag; + u16 err_flag; + u16 hash_hi; + u16 vtag; +}; + +enum atl1e_dma_req_block { + atl1e_dma_req_128 = 0, + atl1e_dma_req_256 = 1, + atl1e_dma_req_512 = 2, + atl1e_dma_req_1024 = 3, + atl1e_dma_req_2048 = 4, + atl1e_dma_req_4096 = 5 +}; + +enum atl1e_rrs_type { + atl1e_rrs_disable = 0, + atl1e_rrs_ipv4 = 1, + atl1e_rrs_ipv4_tcp = 2, + atl1e_rrs_ipv6 = 4, + atl1e_rrs_ipv6_tcp = 8 +}; + +enum atl1e_nic_type { + athr_l1e = 0, + athr_l2e_revA = 1, + athr_l2e_revB = 2 +}; + +struct atl1e_hw_stats { + /* rx */ + unsigned long rx_ok; /* The number of good packet received. */ + unsigned long rx_bcast; /* The number of good broadcast packet received. */ + unsigned long rx_mcast; /* The number of good multicast packet received. */ + unsigned long rx_pause; /* The number of Pause packet received. */ + unsigned long rx_ctrl; /* The number of Control packet received other than Pause frame. */ + unsigned long rx_fcs_err; /* The number of packets with bad FCS. */ + unsigned long rx_len_err; /* The number of packets with mismatch of length field and actual size. */ + unsigned long rx_byte_cnt; /* The number of bytes of good packet received. FCS is NOT included. */ + unsigned long rx_runt; /* The number of packets received that are less than 64 byte long and with good FCS. */ + unsigned long rx_frag; /* The number of packets received that are less than 64 byte long and with bad FCS. */ + unsigned long rx_sz_64; /* The number of good and bad packets received that are 64 byte long. */ + unsigned long rx_sz_65_127; /* The number of good and bad packets received that are between 65 and 127-byte long. */ + unsigned long rx_sz_128_255; /* The number of good and bad packets received that are between 128 and 255-byte long. */ + unsigned long rx_sz_256_511; /* The number of good and bad packets received that are between 256 and 511-byte long. */ + unsigned long rx_sz_512_1023; /* The number of good and bad packets received that are between 512 and 1023-byte long. */ + unsigned long rx_sz_1024_1518; /* The number of good and bad packets received that are between 1024 and 1518-byte long. */ + unsigned long rx_sz_1519_max; /* The number of good and bad packets received that are between 1519-byte and MTU. */ + unsigned long rx_sz_ov; /* The number of good and bad packets received that are more than MTU size truncated by Selene. */ + unsigned long rx_rxf_ov; /* The number of frame dropped due to occurrence of RX FIFO overflow. */ + unsigned long rx_rrd_ov; /* The number of frame dropped due to occurrence of RRD overflow. */ + unsigned long rx_align_err; /* Alignment Error */ + unsigned long rx_bcast_byte_cnt; /* The byte count of broadcast packet received, excluding FCS. */ + unsigned long rx_mcast_byte_cnt; /* The byte count of multicast packet received, excluding FCS. */ + unsigned long rx_err_addr; /* The number of packets dropped due to address filtering. */ + + /* tx */ + unsigned long tx_ok; /* The number of good packet transmitted. */ + unsigned long tx_bcast; /* The number of good broadcast packet transmitted. */ + unsigned long tx_mcast; /* The number of good multicast packet transmitted. */ + unsigned long tx_pause; /* The number of Pause packet transmitted. */ + unsigned long tx_exc_defer; /* The number of packets transmitted with excessive deferral. */ + unsigned long tx_ctrl; /* The number of packets transmitted is a control frame, excluding Pause frame. */ + unsigned long tx_defer; /* The number of packets transmitted that is deferred. */ + unsigned long tx_byte_cnt; /* The number of bytes of data transmitted. FCS is NOT included. */ + unsigned long tx_sz_64; /* The number of good and bad packets transmitted that are 64 byte long. */ + unsigned long tx_sz_65_127; /* The number of good and bad packets transmitted that are between 65 and 127-byte long. */ + unsigned long tx_sz_128_255; /* The number of good and bad packets transmitted that are between 128 and 255-byte long. */ + unsigned long tx_sz_256_511; /* The number of good and bad packets transmitted that are between 256 and 511-byte long. */ + unsigned long tx_sz_512_1023; /* The number of good and bad packets transmitted that are between 512 and 1023-byte long. */ + unsigned long tx_sz_1024_1518; /* The number of good and bad packets transmitted that are between 1024 and 1518-byte long. */ + unsigned long tx_sz_1519_max; /* The number of good and bad packets transmitted that are between 1519-byte and MTU. */ + unsigned long tx_1_col; /* The number of packets subsequently transmitted successfully with a single prior collision. */ + unsigned long tx_2_col; /* The number of packets subsequently transmitted successfully with multiple prior collisions. */ + unsigned long tx_late_col; /* The number of packets transmitted with late collisions. */ + unsigned long tx_abort_col; /* The number of transmit packets aborted due to excessive collisions. */ + unsigned long tx_underrun; /* The number of transmit packets aborted due to transmit FIFO underrun, or TRD FIFO underrun */ + unsigned long tx_rd_eop; /* The number of times that read beyond the EOP into the next frame area when TRD was not written timely */ + unsigned long tx_len_err; /* The number of transmit packets with length field does NOT match the actual frame size. */ + unsigned long tx_trunc; /* The number of transmit packets truncated due to size exceeding MTU. */ + unsigned long tx_bcast_byte; /* The byte count of broadcast packet transmitted, excluding FCS. */ + unsigned long tx_mcast_byte; /* The byte count of multicast packet transmitted, excluding FCS. */ +}; + +struct atl1e_hw { + u8 __iomem *hw_addr; /* inner register address */ + resource_size_t mem_rang; + struct atl1e_adapter *adapter; + enum atl1e_nic_type nic_type; + u16 device_id; + u16 vendor_id; + u16 subsystem_id; + u16 subsystem_vendor_id; + u8 revision_id; + u16 pci_cmd_word; + u8 mac_addr[ETH_ALEN]; + u8 perm_mac_addr[ETH_ALEN]; + u8 preamble_len; + u16 max_frame_size; + u16 rx_jumbo_th; + u16 tx_jumbo_th; + + u16 media_type; +#define MEDIA_TYPE_AUTO_SENSOR 0 +#define MEDIA_TYPE_100M_FULL 1 +#define MEDIA_TYPE_100M_HALF 2 +#define MEDIA_TYPE_10M_FULL 3 +#define MEDIA_TYPE_10M_HALF 4 + + u16 autoneg_advertised; +#define ADVERTISE_10_HALF 0x0001 +#define ADVERTISE_10_FULL 0x0002 +#define ADVERTISE_100_HALF 0x0004 +#define ADVERTISE_100_FULL 0x0008 +#define ADVERTISE_1000_HALF 0x0010 /* Not used, just FYI */ +#define ADVERTISE_1000_FULL 0x0020 + u16 mii_autoneg_adv_reg; + u16 mii_1000t_ctrl_reg; + + u16 imt; /* Interrupt Moderator timer ( 2us resolution) */ + u16 ict; /* Interrupt Clear timer (2us resolution) */ + u32 smb_timer; + u16 rrd_thresh; /* Threshold of number of RRD produced to trigger + interrupt request */ + u16 tpd_thresh; + u16 rx_count_down; /* 2us resolution */ + u16 tx_count_down; + + u8 tpd_burst; /* Number of TPD to prefetch in cache-aligned burst. */ + enum atl1e_rrs_type rrs_type; + u32 base_cpu; + u32 indirect_tab; + + enum atl1e_dma_req_block dmar_block; + enum atl1e_dma_req_block dmaw_block; + u8 dmaw_dly_cnt; + u8 dmar_dly_cnt; + + bool phy_configured; + bool re_autoneg; + bool emi_ca; +}; + +/* + * wrapper around a pointer to a socket buffer, + * so a DMA handle can be stored along with the buffer + */ +struct atl1e_tx_buffer { + struct sk_buff *skb; + u16 length; + dma_addr_t dma; +}; + +struct atl1e_rx_page { + dma_addr_t dma; /* receive rage DMA address */ + u8 *addr; /* receive rage virtual address */ + dma_addr_t write_offset_dma; /* the DMA address which contain the + receive data offset in the page */ + u32 *write_offset_addr; /* the virtaul address which contain + the receive data offset in the page */ + u32 read_offset; /* the offset where we have read */ +}; + +struct atl1e_rx_page_desc { + struct atl1e_rx_page rx_page[AT_PAGE_NUM_PER_QUEUE]; + u8 rx_using; + u16 rx_nxseq; +}; + +/* transmit packet descriptor (tpd) ring */ +struct atl1e_tx_ring { + struct atl1e_tpd_desc *desc; /* descriptor ring virtual address */ + dma_addr_t dma; /* descriptor ring physical address */ + u16 count; /* the count of transmit rings */ + rwlock_t tx_lock; + u16 next_to_use; + atomic_t next_to_clean; + struct atl1e_tx_buffer *tx_buffer; + dma_addr_t cmb_dma; + u32 *cmb; +}; + +/* receive packet descriptor ring */ +struct atl1e_rx_ring { + void *desc; + dma_addr_t dma; + int size; + u32 page_size; /* bytes length of rxf page */ + u32 real_page_size; /* real_page_size = page_size + jumbo + aliagn */ + struct atl1e_rx_page_desc rx_page_desc[AT_MAX_RECEIVE_QUEUE]; +}; + +/* board specific private data structure */ +struct atl1e_adapter { + struct net_device *netdev; + struct pci_dev *pdev; + struct vlan_group *vlgrp; + struct napi_struct napi; + struct mii_if_info mii; /* MII interface info */ + struct atl1e_hw hw; + struct atl1e_hw_stats hw_stats; + struct net_device_stats net_stats; + + bool have_msi; + u32 wol; + u16 link_speed; + u16 link_duplex; + + spinlock_t mdio_lock; + spinlock_t tx_lock; + atomic_t irq_sem; + + struct work_struct reset_task; + struct work_struct link_chg_task; + struct timer_list watchdog_timer; + struct timer_list phy_config_timer; + + /* All Descriptor memory */ + dma_addr_t ring_dma; + void *ring_vir_addr; + int ring_size; + + struct atl1e_tx_ring tx_ring; + struct atl1e_rx_ring rx_ring; + int num_rx_queues; + unsigned long flags; +#define __AT_TESTING 0x0001 +#define __AT_RESETTING 0x0002 +#define __AT_DOWN 0x0003 + + u32 bd_number; /* board number;*/ + u32 pci_state[16]; + u32 *config_space; +}; + +#define AT_WRITE_REG(a, reg, value) ( \ + writel((value), ((a)->hw_addr + reg))) + +#define AT_WRITE_FLUSH(a) (\ + readl((a)->hw_addr)) + +#define AT_READ_REG(a, reg) ( \ + readl((a)->hw_addr + reg)) + +#define AT_WRITE_REGB(a, reg, value) (\ + writeb((value), ((a)->hw_addr + reg))) + +#define AT_READ_REGB(a, reg) (\ + readb((a)->hw_addr + reg)) + +#define AT_WRITE_REGW(a, reg, value) (\ + writew((value), ((a)->hw_addr + reg))) + +#define AT_READ_REGW(a, reg) (\ + readw((a)->hw_addr + reg)) + +#define AT_WRITE_REG_ARRAY(a, reg, offset, value) ( \ + writel((value), (((a)->hw_addr + reg) + ((offset) << 2)))) + +#define AT_READ_REG_ARRAY(a, reg, offset) ( \ + readl(((a)->hw_addr + reg) + ((offset) << 2))) + +extern char atl1e_driver_name[]; +extern char atl1e_driver_version[]; + +extern void atl1e_check_options(struct atl1e_adapter *adapter); +extern int atl1e_up(struct atl1e_adapter *adapter); +extern void atl1e_down(struct atl1e_adapter *adapter); +extern void atl1e_reinit_locked(struct atl1e_adapter *adapter); +extern s32 atl1e_reset_hw(struct atl1e_hw *hw); +extern void atl1e_set_ethtool_ops(struct net_device *netdev); +#endif /* _ATL1_E_H_ */ diff --git a/drivers/net/atl1e/atl1e_ethtool.c b/drivers/net/atl1e/atl1e_ethtool.c new file mode 100644 index 0000000..cdc3b85 --- /dev/null +++ b/drivers/net/atl1e/atl1e_ethtool.c @@ -0,0 +1,405 @@ +/* + * Copyright(c) 2007 Atheros Corporation. All rights reserved. + * + * Derived from Intel e1000 driver + * Copyright(c) 1999 - 2005 Intel Corporation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program; if not, write to the Free Software Foundation, Inc., 59 + * Temple Place - Suite 330, Boston, MA 02111-1307, USA. + * + */ + +#include <linux/netdevice.h> +#include <linux/ethtool.h> + +#include "atl1e.h" + +static int atl1e_get_settings(struct net_device *netdev, + struct ethtool_cmd *ecmd) +{ + struct atl1e_adapter *adapter = netdev_priv(netdev); + struct atl1e_hw *hw = &adapter->hw; + + ecmd->supported = (SUPPORTED_10baseT_Half | + SUPPORTED_10baseT_Full | + SUPPORTED_100baseT_Half | + SUPPORTED_100baseT_Full | + SUPPORTED_Autoneg | + SUPPORTED_TP); + if (hw->nic_type == athr_l1e) + ecmd->supported |= SUPPORTED_1000baseT_Full; + + ecmd->advertising = ADVERTISED_TP; + + ecmd->advertising |= ADVERTISED_Autoneg; + ecmd->advertising |= hw->autoneg_advertised; + + ecmd->port = PORT_TP; + ecmd->phy_address = 0; + ecmd->transceiver = XCVR_INTERNAL; + + if (adapter->link_speed != SPEED_0) { + ecmd->speed = adapter->link_speed; + if (adapter->link_duplex == FULL_DUPLEX) + ecmd->duplex = DUPLEX_FULL; + else + ecmd->duplex = DUPLEX_HALF; + } else { + ecmd->speed = -1; + ecmd->duplex = -1; + } + + ecmd->autoneg = AUTONEG_ENABLE; + return 0; +} + +static int atl1e_set_settings(struct net_device *netdev, + struct ethtool_cmd *ecmd) +{ + struct atl1e_adapter *adapter = netdev_priv(netdev); + struct atl1e_hw *hw = &adapter->hw; + + while (test_and_set_bit(__AT_RESETTING, &adapter->flags)) + msleep(1); + + if (ecmd->autoneg == AUTONEG_ENABLE) { + u16 adv4, adv9; + + if ((ecmd->advertising&ADVERTISE_1000_FULL)) { + if (hw->nic_type == athr_l1e) { + hw->autoneg_advertised = + ecmd->advertising & AT_ADV_MASK; + } else { + clear_bit(__AT_RESETTING, &adapter->flags); + return -EINVAL; + } + } else if (ecmd->advertising&ADVERTISE_1000_HALF) { + clear_bit(__AT_RESETTING, &adapter->flags); + return -EINVAL; + } else { + hw->autoneg_advertised = + ecmd->advertising & AT_ADV_MASK; + } + ecmd->advertising = hw->autoneg_advertised | + ADVERTISED_TP | ADVERTISED_Autoneg; + + adv4 = hw->mii_autoneg_adv_reg & ~MII_AR_SPEED_MASK; + adv9 = hw->mii_1000t_ctrl_reg & ~MII_AT001_CR_1000T_SPEED_MASK; + if (hw->autoneg_advertised & ADVERTISE_10_HALF) + adv4 |= MII_AR_10T_HD_CAPS; + if (hw->autoneg_advertised & ADVERTISE_10_FULL) + adv4 |= MII_AR_10T_FD_CAPS; + if (hw->autoneg_advertised & ADVERTISE_100_HALF) + adv4 |= MII_AR_100TX_HD_CAPS; + if (hw->autoneg_advertised & ADVERTISE_100_FULL) + adv4 |= MII_AR_100TX_FD_CAPS; + if (hw->autoneg_advertised & ADVERTISE_1000_FULL) + adv9 |= MII_AT001_CR_1000T_FD_CAPS; + + if (adv4 != hw->mii_autoneg_adv_reg || + adv9 != hw->mii_1000t_ctrl_reg) { + hw->mii_autoneg_adv_reg = adv4; + hw->mii_1000t_ctrl_reg = adv9; + hw->re_autoneg = true; + } + + } else { + clear_bit(__AT_RESETTING, &adapter->flags); + return -EINVAL; + } + + /* reset the link */ + + if (netif_running(adapter->netdev)) { + atl1e_down(adapter); + atl1e_up(adapter); + } else + atl1e_reset_hw(&adapter->hw); + + clear_bit(__AT_RESETTING, &adapter->flags); + return 0; +} + +static u32 atl1e_get_tx_csum(struct net_device *netdev) +{ + return (netdev->features & NETIF_F_HW_CSUM) != 0; +} + +static u32 atl1e_get_msglevel(struct net_device *netdev) +{ +#ifdef DBG + return 1; +#else + return 0; +#endif +} + +static void atl1e_set_msglevel(struct net_device *netdev, u32 data) +{ +} + +static int atl1e_get_regs_len(struct net_device *netdev) +{ + return AT_REGS_LEN * sizeof(u32); +} + +static void atl1e_get_regs(struct net_device *netdev, + struct ethtool_regs *regs, void *p) +{ + struct atl1e_adapter *adapter = netdev_priv(netdev); + struct atl1e_hw *hw = &adapter->hw; + u32 *regs_buff = p; + u16 phy_data; + + memset(p, 0, AT_REGS_LEN * sizeof(u32)); + + regs->version = (1 << 24) | (hw->revision_id << 16) | hw->device_id; + + regs_buff[0] = AT_READ_REG(hw, REG_VPD_CAP); + regs_buff[1] = AT_READ_REG(hw, REG_SPI_FLASH_CTRL); + regs_buff[2] = AT_READ_REG(hw, REG_SPI_FLASH_CONFIG); + regs_buff[3] = AT_READ_REG(hw, REG_TWSI_CTRL); + regs_buff[4] = AT_READ_REG(hw, REG_PCIE_DEV_MISC_CTRL); + regs_buff[5] = AT_READ_REG(hw, REG_MASTER_CTRL); + regs_buff[6] = AT_READ_REG(hw, REG_MANUAL_TIMER_INIT); + regs_buff[7] = AT_READ_REG(hw, REG_IRQ_MODU_TIMER_INIT); + regs_buff[8] = AT_READ_REG(hw, REG_GPHY_CTRL); + regs_buff[9] = AT_READ_REG(hw, REG_CMBDISDMA_TIMER); + regs_buff[10] = AT_READ_REG(hw, REG_IDLE_STATUS); + regs_buff[11] = AT_READ_REG(hw, REG_MDIO_CTRL); + regs_buff[12] = AT_READ_REG(hw, REG_SERDES_LOCK); + regs_buff[13] = AT_READ_REG(hw, REG_MAC_CTRL); + regs_buff[14] = AT_READ_REG(hw, REG_MAC_IPG_IFG); + regs_buff[15] = AT_READ_REG(hw, REG_MAC_STA_ADDR); + regs_buff[16] = AT_READ_REG(hw, REG_MAC_STA_ADDR+4); + regs_buff[17] = AT_READ_REG(hw, REG_RX_HASH_TABLE); + regs_buff[18] = AT_READ_REG(hw, REG_RX_HASH_TABLE+4); + regs_buff[19] = AT_READ_REG(hw, REG_MAC_HALF_DUPLX_CTRL); + regs_buff[20] = AT_READ_REG(hw, REG_MTU); + regs_buff[21] = AT_READ_REG(hw, REG_WOL_CTRL); + regs_buff[22] = AT_READ_REG(hw, REG_SRAM_TRD_ADDR); + regs_buff[23] = AT_READ_REG(hw, REG_SRAM_TRD_LEN); + regs_buff[24] = AT_READ_REG(hw, REG_SRAM_RXF_ADDR); + regs_buff[25] = AT_READ_REG(hw, REG_SRAM_RXF_LEN); + regs_buff[26] = AT_READ_REG(hw, REG_SRAM_TXF_ADDR); + regs_buff[27] = AT_READ_REG(hw, REG_SRAM_TXF_LEN); + regs_buff[28] = AT_READ_REG(hw, REG_SRAM_TCPH_ADDR); + regs_buff[29] = AT_READ_REG(hw, REG_SRAM_PKTH_ADDR); + + atl1e_read_phy_reg(hw, MII_BMCR, &phy_data); + regs_buff[73] = (u32)phy_data; + atl1e_read_phy_reg(hw, MII_BMSR, &phy_data); + regs_buff[74] = (u32)phy_data; +} + +static int atl1e_get_eeprom_len(struct net_device *netdev) +{ + struct atl1e_adapter *adapter = netdev_priv(netdev); + + if (!atl1e_check_eeprom_exist(&adapter->hw)) + return AT_EEPROM_LEN; + else + return 0; +} + +static int atl1e_get_eeprom(struct net_device *netdev, + struct ethtool_eeprom *eeprom, u8 *bytes) +{ + struct atl1e_adapter *adapter = netdev_priv(netdev); + struct atl1e_hw *hw = &adapter->hw; + u32 *eeprom_buff; + int first_dword, last_dword; + int ret_val = 0; + int i; + + if (eeprom->len == 0) + return -EINVAL; + + if (atl1e_check_eeprom_exist(hw)) /* not exist */ + return -EINVAL; + + eeprom->magic = hw->vendor_id | (hw->device_id << 16); + + first_dword = eeprom->offset >> 2; + last_dword = (eeprom->offset + eeprom->len - 1) >> 2; + + eeprom_buff = kmalloc(sizeof(u32) * + (last_dword - first_dword + 1), GFP_KERNEL); + if (eeprom_buff == NULL) + return -ENOMEM; + + for (i = first_dword; i < last_dword; i++) { + if (!atl1e_read_eeprom(hw, i * 4, &(eeprom_buff[i-first_dword]))) { + kfree(eeprom_buff); + return -EIO; + } + } + + memcpy(bytes, (u8 *)eeprom_buff + (eeprom->offset & 3), + eeprom->len); + kfree(eeprom_buff); + + return ret_val; +} + +static int atl1e_set_eeprom(struct net_device *netdev, + struct ethtool_eeprom *eeprom, u8 *bytes) +{ + struct atl1e_adapter *adapter = netdev_priv(netdev); + struct atl1e_hw *hw = &adapter->hw; + u32 *eeprom_buff; + u32 *ptr; + int first_dword, last_dword; + int ret_val = 0; + int i; + + if (eeprom->len == 0) + return -EOPNOTSUPP; + + if (eeprom->magic != (hw->vendor_id | (hw->device_id << 16))) + return -EINVAL; + + first_dword = eeprom->offset >> 2; + last_dword = (eeprom->offset + eeprom->len - 1) >> 2; + eeprom_buff = kmalloc(AT_EEPROM_LEN, GFP_KERNEL); + if (eeprom_buff == NULL) + return -ENOMEM; + + ptr = (u32 *)eeprom_buff; + + if (eeprom->offset & 3) { + /* need read/modify/write of first changed EEPROM word */ + /* only the second byte of the word is being modified */ + if (!atl1e_read_eeprom(hw, first_dword * 4, &(eeprom_buff[0]))) { + ret_val = -EIO; + goto out; + } + ptr++; + } + if (((eeprom->offset + eeprom->len) & 3)) { + /* need read/modify/write of last changed EEPROM word */ + /* only the first byte of the word is being modified */ + + if (!atl1e_read_eeprom(hw, last_dword * 4, + &(eeprom_buff[last_dword - first_dword]))) { + ret_val = -EIO; + goto out; + } + } + + /* Device's eeprom is always little-endian, word addressable */ + memcpy(ptr, bytes, eeprom->len); + + for (i = 0; i < last_dword - first_dword + 1; i++) { + if (!atl1e_write_eeprom(hw, ((first_dword + i) * 4), + eeprom_buff[i])) { + ret_val = -EIO; + goto out; + } + } +out: + kfree(eeprom_buff); + return ret_val; +} + +static void atl1e_get_drvinfo(struct net_device *netdev, + struct ethtool_drvinfo *drvinfo) +{ + struct atl1e_adapter *adapter = netdev_priv(netdev); + + strncpy(drvinfo->driver, atl1e_driver_name, 32); + strncpy(drvinfo->version, atl1e_driver_version, 32); + strncpy(drvinfo->fw_version, "L1e", 32); + strncpy(drvinfo->bus_info, pci_name(adapter->pdev), 32); + drvinfo->n_stats = 0; + drvinfo->testinfo_len = 0; + drvinfo->regdump_len = atl1e_get_regs_len(netdev); + drvinfo->eedump_len = atl1e_get_eeprom_len(netdev); +} + +static void atl1e_get_wol(struct net_device *netdev, + struct ethtool_wolinfo *wol) +{ + struct atl1e_adapter *adapter = netdev_priv(netdev); + + wol->supported = WAKE_MAGIC | WAKE_PHY; + wol->wolopts = 0; + + if (adapter->wol & AT_WUFC_EX) + wol->wolopts |= WAKE_UCAST; + if (adapter->wol & AT_WUFC_MC) + wol->wolopts |= WAKE_MCAST; + if (adapter->wol & AT_WUFC_BC) + wol->wolopts |= WAKE_BCAST; + if (adapter->wol & AT_WUFC_MAG) + wol->wolopts |= WAKE_MAGIC; + if (adapter->wol & AT_WUFC_LNKC) + wol->wolopts |= WAKE_PHY; + + return; +} + +static int atl1e_set_wol(struct net_device *netdev, struct ethtool_wolinfo *wol) +{ + struct atl1e_adapter *adapter = netdev_priv(netdev); + + if (wol->wolopts & (WAKE_ARP | WAKE_MAGICSECURE | + WAKE_MCAST | WAKE_BCAST | WAKE_MCAST)) + return -EOPNOTSUPP; + /* these settings will always override what we currently have */ + adapter->wol = 0; + + if (wol->wolopts & WAKE_MAGIC) + adapter->wol |= AT_WUFC_MAG; + if (wol->wolopts & WAKE_PHY) + adapter->wol |= AT_WUFC_LNKC; + + return 0; +} + +static int atl1e_nway_reset(struct net_device *netdev) +{ + struct atl1e_adapter *adapter = netdev_priv(netdev); + if (netif_running(netdev)) + atl1e_reinit_locked(adapter); + return 0; +} + +static struct ethtool_ops atl1e_ethtool_ops = { + .get_settings = atl1e_get_settings, + .set_settings = atl1e_set_settings, + .get_drvinfo = atl1e_get_drvinfo, + .get_regs_len = atl1e_get_regs_len, + .get_regs = atl1e_get_regs, + .get_wol = atl1e_get_wol, + .set_wol = atl1e_set_wol, + .get_msglevel = atl1e_get_msglevel, + .set_msglevel = atl1e_set_msglevel, + .nway_reset = atl1e_nway_reset, + .get_link = ethtool_op_get_link, + .get_eeprom_len = atl1e_get_eeprom_len, + .get_eeprom = atl1e_get_eeprom, + .set_eeprom = atl1e_set_eeprom, + .get_tx_csum = atl1e_get_tx_csum, + .get_sg = ethtool_op_get_sg, + .set_sg = ethtool_op_set_sg, +#ifdef NETIF_F_TSO + .get_tso = ethtool_op_get_tso, +#endif +}; + +void atl1e_set_ethtool_ops(struct net_device *netdev) +{ + SET_ETHTOOL_OPS(netdev, &atl1e_ethtool_ops); +} diff --git a/drivers/net/atl1e/atl1e_hw.c b/drivers/net/atl1e/atl1e_hw.c new file mode 100644 index 0000000..949e753 --- /dev/null +++ b/drivers/net/atl1e/atl1e_hw.c @@ -0,0 +1,664 @@ +/* + * Copyright(c) 2007 Atheros Corporation. All rights reserved. + * + * Derived from Intel e1000 driver + * Copyright(c) 1999 - 2005 Intel Corporation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program; if not, write to the Free Software Foundation, Inc., 59 + * Temple Place - Suite 330, Boston, MA 02111-1307, USA. + */ +#include <linux/pci.h> +#include <linux/delay.h> +#include <linux/mii.h> +#include <linux/crc32.h> + +#include "atl1e.h" + +/* + * check_eeprom_exist + * return 0 if eeprom exist + */ +int atl1e_check_eeprom_exist(struct atl1e_hw *hw) +{ + u32 value; + + value = AT_READ_REG(hw, REG_SPI_FLASH_CTRL); + if (value & SPI_FLASH_CTRL_EN_VPD) { + value &= ~SPI_FLASH_CTRL_EN_VPD; + AT_WRITE_REG(hw, REG_SPI_FLASH_CTRL, value); + } + value = AT_READ_REGW(hw, REG_PCIE_CAP_LIST); + return ((value & 0xFF00) == 0x6C00) ? 0 : 1; +} + +void atl1e_hw_set_mac_addr(struct atl1e_hw *hw) +{ + u32 value; + /* + * 00-0B-6A-F6-00-DC + * 0: 6AF600DC 1: 000B + * low dword + */ + value = (((u32)hw->mac_addr[2]) << 24) | + (((u32)hw->mac_addr[3]) << 16) | + (((u32)hw->mac_addr[4]) << 8) | + (((u32)hw->mac_addr[5])) ; + AT_WRITE_REG_ARRAY(hw, REG_MAC_STA_ADDR, 0, value); + /* hight dword */ + value = (((u32)hw->mac_addr[0]) << 8) | + (((u32)hw->mac_addr[1])) ; + AT_WRITE_REG_ARRAY(hw, REG_MAC_STA_ADDR, 1, value); +} + +/* + * atl1e_get_permanent_address + * return 0 if get valid mac address, + */ +static int atl1e_get_permanent_address(struct atl1e_hw *hw) +{ + u32 addr[2]; + u32 i; + u32 twsi_ctrl_data; + u8 eth_addr[ETH_ALEN]; + + if (is_valid_ether_addr(hw->perm_mac_addr)) + return 0; + + /* init */ + addr[0] = addr[1] = 0; + + if (!atl1e_check_eeprom_exist(hw)) { + /* eeprom exist */ + twsi_ctrl_data = AT_READ_REG(hw, REG_TWSI_CTRL); + twsi_ctrl_data |= TWSI_CTRL_SW_LDSTART; + AT_WRITE_REG(hw, REG_TWSI_CTRL, twsi_ctrl_data); + for (i = 0; i < AT_TWSI_EEPROM_TIMEOUT; i++) { + msleep(10); + twsi_ctrl_data = AT_READ_REG(hw, REG_TWSI_CTRL); + if ((twsi_ctrl_data & TWSI_CTRL_SW_LDSTART) == 0) + break; + } + if (i >= AT_TWSI_EEPROM_TIMEOUT) + return AT_ERR_TIMEOUT; + } + + /* maybe MAC-address is from BIOS */ + addr[0] = AT_READ_REG(hw, REG_MAC_STA_ADDR); + addr[1] = AT_READ_REG(hw, REG_MAC_STA_ADDR + 4); + *(u32 *) ð_addr[2] = swab32(addr[0]); + *(u16 *) ð_addr[0] = swab16(*(u16 *)&addr[1]); + + if (is_valid_ether_addr(eth_addr)) { + memcpy(hw->perm_mac_addr, eth_addr, ETH_ALEN); + return 0; + } + + return AT_ERR_EEPROM; +} + +bool atl1e_write_eeprom(struct atl1e_hw *hw, u32 offset, u32 value) +{ + return true; +} + +bool atl1e_read_eeprom(struct atl1e_hw *hw, u32 offset, u32 *p_value) +{ + int i; + u32 control; + + if (offset & 3) + return false; /* address do not align */ + + AT_WRITE_REG(hw, REG_VPD_DATA, 0); + control = (offset & VPD_CAP_VPD_ADDR_MASK) << VPD_CAP_VPD_ADDR_SHIFT; + AT_WRITE_REG(hw, REG_VPD_CAP, control); + + for (i = 0; i < 10; i++) { + msleep(2); + control = AT_READ_REG(hw, REG_VPD_CAP); + if (control & VPD_CAP_VPD_FLAG) + break; + } + if (control & VPD_CAP_VPD_FLAG) { + *p_value = AT_READ_REG(hw, REG_VPD_DATA); + return true; + } + return false; /* timeout */ +} + +void atl1e_force_ps(struct atl1e_hw *hw) +{ + AT_WRITE_REGW(hw, REG_GPHY_CTRL, + GPHY_CTRL_PW_WOL_DIS | GPHY_CTRL_EXT_RESET); +} + +/* + * Reads the adapter's MAC address from the EEPROM + * + * hw - Struct containing variables accessed by shared code + */ +int atl1e_read_mac_addr(struct atl1e_hw *hw) +{ + int err = 0; + + err = atl1e_get_permanent_address(hw); + if (err) + return AT_ERR_EEPROM; + memcpy(hw->mac_addr, hw->perm_mac_addr, sizeof(hw->perm_mac_addr)); + return 0; +} + +/* + * atl1e_hash_mc_addr + * purpose + * set hash value for a multicast address + * hash calcu processing : + * 1. calcu 32bit CRC for multicast address + * 2. reverse crc with MSB to LSB + */ +u32 atl1e_hash_mc_addr(struct atl1e_hw *hw, u8 *mc_addr) +{ + u32 crc32; + u32 value = 0; + int i; + + crc32 = ether_crc_le(6, mc_addr); + crc32 = ~crc32; + for (i = 0; i < 32; i++) + value |= (((crc32 >> i) & 1) << (31 - i)); + + return value; +} + +/* + * Sets the bit in the multicast table corresponding to the hash value. + * hw - Struct containing variables accessed by shared code + * hash_value - Multicast address hash value + */ +void atl1e_hash_set(struct atl1e_hw *hw, u32 hash_value) +{ + u32 hash_bit, hash_reg; + u32 mta; + + /* + * The HASH Table is a register array of 2 32-bit registers. + * It is treated like an array of 64 bits. We want to set + * bit BitArray[hash_value]. So we figure out what register + * the bit is in, read it, OR in the new bit, then write + * back the new value. The register is determined by the + * upper 7 bits of the hash value and the bit within that + * register are determined by the lower 5 bits of the value. + */ + hash_reg = (hash_value >> 31) & 0x1; + hash_bit = (hash_value >> 26) & 0x1F; + + mta = AT_READ_REG_ARRAY(hw, REG_RX_HASH_TABLE, hash_reg); + + mta |= (1 << hash_bit); + + AT_WRITE_REG_ARRAY(hw, REG_RX_HASH_TABLE, hash_reg, mta); +} +/* + * Reads the value from a PHY register + * hw - Struct containing variables accessed by shared code + * reg_addr - address of the PHY register to read + */ +int atl1e_read_phy_reg(struct atl1e_hw *hw, u16 reg_addr, u16 *phy_data) +{ + u32 val; + int i; + + val = ((u32)(reg_addr & MDIO_REG_ADDR_MASK)) << MDIO_REG_ADDR_SHIFT | + MDIO_START | MDIO_SUP_PREAMBLE | MDIO_RW | + MDIO_CLK_25_4 << MDIO_CLK_SEL_SHIFT; + + AT_WRITE_REG(hw, REG_MDIO_CTRL, val); + + wmb(); + + for (i = 0; i < MDIO_WAIT_TIMES; i++) { + udelay(2); + val = AT_READ_REG(hw, REG_MDIO_CTRL); + if (!(val & (MDIO_START | MDIO_BUSY))) + break; + wmb(); + } + if (!(val & (MDIO_START | MDIO_BUSY))) { + *phy_data = (u16)val; + return 0; + } + + return AT_ERR_PHY; +} + +/* + * Writes a value to a PHY register + * hw - Struct containing variables accessed by shared code + * reg_addr - address of the PHY register to write + * data - data to write to the PHY + */ +int atl1e_write_phy_reg(struct atl1e_hw *hw, u32 reg_addr, u16 phy_data) +{ + int i; + u32 val; + + val = ((u32)(phy_data & MDIO_DATA_MASK)) << MDIO_DATA_SHIFT | + (reg_addr&MDIO_REG_ADDR_MASK) << MDIO_REG_ADDR_SHIFT | + MDIO_SUP_PREAMBLE | + MDIO_START | + MDIO_CLK_25_4 << MDIO_CLK_SEL_SHIFT; + + AT_WRITE_REG(hw, REG_MDIO_CTRL, val); + wmb(); + + for (i = 0; i < MDIO_WAIT_TIMES; i++) { + udelay(2); + val = AT_READ_REG(hw, REG_MDIO_CTRL); + if (!(val & (MDIO_START | MDIO_BUSY))) + break; + wmb(); + } + + if (!(val & (MDIO_START | MDIO_BUSY))) + return 0; + + return AT_ERR_PHY; +} + +/* + * atl1e_init_pcie - init PCIE module + */ +static void atl1e_init_pcie(struct atl1e_hw *hw) +{ + u32 value; + /* comment 2lines below to save more power when sususpend + value = LTSSM_TEST_MODE_DEF; + AT_WRITE_REG(hw, REG_LTSSM_TEST_MODE, value); + */ + + /* pcie flow control mode change */ + value = AT_READ_REG(hw, 0x1008); + value |= 0x8000; + AT_WRITE_REG(hw, 0x1008, value); +} +/* + * Configures PHY autoneg and flow control advertisement settings + * + * hw - Struct containing variables accessed by shared code + */ +static int atl1e_phy_setup_autoneg_adv(struct atl1e_hw *hw) +{ + s32 ret_val; + u16 mii_autoneg_adv_reg; + u16 mii_1000t_ctrl_reg; + + if (0 != hw->mii_autoneg_adv_reg) + return 0; + /* Read the MII Auto-Neg Advertisement Register (Address 4/9). */ + mii_autoneg_adv_reg = MII_AR_DEFAULT_CAP_MASK; + mii_1000t_ctrl_reg = MII_AT001_CR_1000T_DEFAULT_CAP_MASK; + + /* + * Need to parse autoneg_advertised and set up + * the appropriate PHY registers. First we will parse for + * autoneg_advertised software override. Since we can advertise + * a plethora of combinations, we need to check each bit + * individually. + */ + + /* + * First we clear all the 10/100 mb speed bits in the Auto-Neg + * Advertisement Register (Address 4) and the 1000 mb speed bits in + * the 1000Base-T control Register (Address 9). + */ + mii_autoneg_adv_reg &= ~MII_AR_SPEED_MASK; + mii_1000t_ctrl_reg &= ~MII_AT001_CR_1000T_SPEED_MASK; + + /* + * Need to parse MediaType and setup the + * appropriate PHY registers. + */ + switch (hw->media_type) { + case MEDIA_TYPE_AUTO_SENSOR: + mii_autoneg_adv_reg |= (MII_AR_10T_HD_CAPS | + MII_AR_10T_FD_CAPS | + MII_AR_100TX_HD_CAPS | + MII_AR_100TX_FD_CAPS); + hw->autoneg_advertised = ADVERTISE_10_HALF | + ADVERTISE_10_FULL | + ADVERTISE_100_HALF | + ADVERTISE_100_FULL; + if (hw->nic_type == athr_l1e) { + mii_1000t_ctrl_reg |= + MII_AT001_CR_1000T_FD_CAPS; + hw->autoneg_advertised |= ADVERTISE_1000_FULL; + } + break; + + case MEDIA_TYPE_100M_FULL: + mii_autoneg_adv_reg |= MII_AR_100TX_FD_CAPS; + hw->autoneg_advertised = ADVERTISE_100_FULL; + break; + + case MEDIA_TYPE_100M_HALF: + mii_autoneg_adv_reg |= MII_AR_100TX_HD_CAPS; + hw->autoneg_advertised = ADVERTISE_100_HALF; + break; + + case MEDIA_TYPE_10M_FULL: + mii_autoneg_adv_reg |= MII_AR_10T_FD_CAPS; + hw->autoneg_advertised = ADVERTISE_10_FULL; + break; + + default: + mii_autoneg_adv_reg |= MII_AR_10T_HD_CAPS; + hw->autoneg_advertised = ADVERTISE_10_HALF; + break; + } + + /* flow control fixed to enable all */ + mii_autoneg_adv_reg |= (MII_AR_ASM_DIR | MII_AR_PAUSE); + + hw->mii_autoneg_adv_reg = mii_autoneg_adv_reg; + hw->mii_1000t_ctrl_reg = mii_1000t_ctrl_reg; + + ret_val = atl1e_write_phy_reg(hw, MII_ADVERTISE, mii_autoneg_adv_reg); + if (ret_val) + return ret_val; + + if (hw->nic_type == athr_l1e || hw->nic_type == athr_l2e_revA) { + ret_val = atl1e_write_phy_reg(hw, MII_AT001_CR, + mii_1000t_ctrl_reg); + if (ret_val) + return ret_val; + } + + return 0; +} + + +/* + * Resets the PHY and make all config validate + * + * hw - Struct containing variables accessed by shared code + * + * Sets bit 15 and 12 of the MII control regiser (for F001 bug) + */ +int atl1e_phy_commit(struct atl1e_hw *hw) +{ + struct atl1e_adapter *adapter = (struct atl1e_adapter *)hw->adapter; + struct pci_dev *pdev = adapter->pdev; + int ret_val; + u16 phy_data; + + phy_data = MII_CR_RESET | MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG; + + ret_val = atl1e_write_phy_reg(hw, MII_BMCR, phy_data); + if (ret_val) { + u32 val; + int i; + /************************************** + * pcie serdes link may be down ! + **************************************/ + for (i = 0; i < 25; i++) { + msleep(1); + val = AT_READ_REG(hw, REG_MDIO_CTRL); + if (!(val & (MDIO_START | MDIO_BUSY))) + break; + } + + if (0 != (val & (MDIO_START | MDIO_BUSY))) { + dev_err(&pdev->dev, + "pcie linkdown at least for 25ms\n"); + return ret_val; + } + + dev_err(&pdev->dev, "pcie linkup after %d ms\n", i); + } + return 0; +} + +int atl1e_phy_init(struct atl1e_hw *hw) +{ + struct atl1e_adapter *adapter = (struct atl1e_adapter *)hw->adapter; + struct pci_dev *pdev = adapter->pdev; + s32 ret_val; + u16 phy_val; + + if (hw->phy_configured) { + if (hw->re_autoneg) { + hw->re_autoneg = false; + return atl1e_restart_autoneg(hw); + } + return 0; + } + + /* RESET GPHY Core */ + AT_WRITE_REGW(hw, REG_GPHY_CTRL, GPHY_CTRL_DEFAULT); + msleep(2); + AT_WRITE_REGW(hw, REG_GPHY_CTRL, GPHY_CTRL_DEFAULT | + GPHY_CTRL_EXT_RESET); + msleep(2); + + /* patches */ + /* p1. eable hibernation mode */ + ret_val = atl1e_write_phy_reg(hw, MII_DBG_ADDR, 0xB); + if (ret_val) + return ret_val; + ret_val = atl1e_write_phy_reg(hw, MII_DBG_DATA, 0xBC00); + if (ret_val) + return ret_val; + /* p2. set Class A/B for all modes */ + ret_val = atl1e_write_phy_reg(hw, MII_DBG_ADDR, 0); + if (ret_val) + return ret_val; + phy_val = 0x02ef; + /* remove Class AB */ + /* phy_val = hw->emi_ca ? 0x02ef : 0x02df; */ + ret_val = atl1e_write_phy_reg(hw, MII_DBG_DATA, phy_val); + if (ret_val) + return ret_val; + /* p3. 10B ??? */ + ret_val = atl1e_write_phy_reg(hw, MII_DBG_ADDR, 0x12); + if (ret_val) + return ret_val; + ret_val = atl1e_write_phy_reg(hw, MII_DBG_DATA, 0x4C04); + if (ret_val) + return ret_val; + /* p4. 1000T power */ + ret_val = atl1e_write_phy_reg(hw, MII_DBG_ADDR, 0x4); + if (ret_val) + return ret_val; + ret_val = atl1e_write_phy_reg(hw, MII_DBG_DATA, 0x8BBB); + if (ret_val) + return ret_val; + + ret_val = atl1e_write_phy_reg(hw, MII_DBG_ADDR, 0x5); + if (ret_val) + return ret_val; + ret_val = atl1e_write_phy_reg(hw, MII_DBG_DATA, 0x2C46); + if (ret_val) + return ret_val; + + msleep(1); + + /*Enable PHY LinkChange Interrupt */ + ret_val = atl1e_write_phy_reg(hw, MII_INT_CTRL, 0xC00); + if (ret_val) { + dev_err(&pdev->dev, "Error enable PHY linkChange Interrupt\n"); + return ret_val; + } + /* setup AutoNeg parameters */ + ret_val = atl1e_phy_setup_autoneg_adv(hw); + if (ret_val) { + dev_err(&pdev->dev, "Error Setting up Auto-Negotiation\n"); + return ret_val; + } + /* SW.Reset & En-Auto-Neg to restart Auto-Neg*/ + dev_dbg(&pdev->dev, "Restarting Auto-Neg"); + ret_val = atl1e_phy_commit(hw); + if (ret_val) { + dev_err(&pdev->dev, "Error Resetting the phy"); + return ret_val; + } + + hw->phy_configured = true; + + return 0; +} + +/* + * Reset the transmit and receive units; mask and clear all interrupts. + * hw - Struct containing variables accessed by shared code + * return : 0 or idle status (if error) + */ +int atl1e_reset_hw(struct atl1e_hw *hw) +{ + struct atl1e_adapter *adapter = (struct atl1e_adapter *)hw->adapter; + struct pci_dev *pdev = adapter->pdev; + + u32 idle_status_data = 0; + u16 pci_cfg_cmd_word = 0; + int timeout = 0; + + /* Workaround for PCI problem when BIOS sets MMRBC incorrectly. */ + pci_read_config_word(pdev, PCI_REG_COMMAND, &pci_cfg_cmd_word); + if ((pci_cfg_cmd_word & (CMD_IO_SPACE | + CMD_MEMORY_SPACE | CMD_BUS_MASTER)) + != (CMD_IO_SPACE | CMD_MEMORY_SPACE | CMD_BUS_MASTER)) { + pci_cfg_cmd_word |= (CMD_IO_SPACE | + CMD_MEMORY_SPACE | CMD_BUS_MASTER); + pci_write_config_word(pdev, PCI_REG_COMMAND, pci_cfg_cmd_word); + } + + /* + * Issue Soft Reset to the MAC. This will reset the chip's + * transmit, receive, DMA. It will not effect + * the current PCI configuration. The global reset bit is self- + * clearing, and should clear within a microsecond. + */ + AT_WRITE_REG(hw, REG_MASTER_CTRL, + MASTER_CTRL_LED_MODE | MASTER_CTRL_SOFT_RST); + wmb(); + msleep(1); + + /* Wait at least 10ms for All module to be Idle */ + for (timeout = 0; timeout < AT_HW_MAX_IDLE_DELAY; timeout++) { + idle_status_data = AT_READ_REG(hw, REG_IDLE_STATUS); + if (idle_status_data == 0) + break; + msleep(1); + cpu_relax(); + } + + if (timeout >= AT_HW_MAX_IDLE_DELAY) { + dev_err(&pdev->dev, + "MAC state machine cann't be idle since" + " disabled for 10ms second\n"); + return AT_ERR_TIMEOUT; + } + + return 0; +} + + +/* + * Performs basic configuration of the adapter. + * + * hw - Struct containing variables accessed by shared code + * Assumes that the controller has previously been reset and is in a + * post-reset uninitialized state. Initializes multicast table, + * and Calls routines to setup link + * Leaves the transmit and receive units disabled and uninitialized. + */ +int atl1e_init_hw(struct atl1e_hw *hw) +{ + s32 ret_val = 0; + + atl1e_init_pcie(hw); + + /* Zero out the Multicast HASH table */ + /* clear the old settings from the multicast hash table */ + AT_WRITE_REG(hw, REG_RX_HASH_TABLE, 0); + AT_WRITE_REG_ARRAY(hw, REG_RX_HASH_TABLE, 1, 0); + + ret_val = atl1e_phy_init(hw); + + return ret_val; +} + +/* + * Detects the current speed and duplex settings of the hardware. + * + * hw - Struct containing variables accessed by shared code + * speed - Speed of the connection + * duplex - Duplex setting of the connection + */ +int atl1e_get_speed_and_duplex(struct atl1e_hw *hw, u16 *speed, u16 *duplex) +{ + int err; + u16 phy_data; + + /* Read PHY Specific Status Register (17) */ + err = atl1e_read_phy_reg(hw, MII_AT001_PSSR, &phy_data); + if (err) + return err; + + if (!(phy_data & MII_AT001_PSSR_SPD_DPLX_RESOLVED)) + return AT_ERR_PHY_RES; + + switch (phy_data & MII_AT001_PSSR_SPEED) { + case MII_AT001_PSSR_1000MBS: + *speed = SPEED_1000; + break; + case MII_AT001_PSSR_100MBS: + *speed = SPEED_100; + break; + case MII_AT001_PSSR_10MBS: + *speed = SPEED_10; + break; + default: + return AT_ERR_PHY_SPEED; + break; + } + + if (phy_data & MII_AT001_PSSR_DPLX) + *duplex = FULL_DUPLEX; + else + *duplex = HALF_DUPLEX; + + return 0; +} + +int atl1e_restart_autoneg(struct atl1e_hw *hw) +{ + int err = 0; + + err = atl1e_write_phy_reg(hw, MII_ADVERTISE, hw->mii_autoneg_adv_reg); + if (err) + return err; + + if (hw->nic_type == athr_l1e || hw->nic_type == athr_l2e_revA) { + err = atl1e_write_phy_reg(hw, MII_AT001_CR, + hw->mii_1000t_ctrl_reg); + if (err) + return err; + } + + err = atl1e_write_phy_reg(hw, MII_BMCR, + MII_CR_RESET | MII_CR_AUTO_NEG_EN | + MII_CR_RESTART_AUTO_NEG); + return err; +} + diff --git a/drivers/net/atl1e/atl1e_hw.h b/drivers/net/atl1e/atl1e_hw.h new file mode 100644 index 0000000..5ea2f4d --- /dev/null +++ b/drivers/net/atl1e/atl1e_hw.h @@ -0,0 +1,793 @@ +/* + * Copyright(c) 2007 Atheros Corporation. All rights reserved. + * + * Derived from Intel e1000 driver + * Copyright(c) 1999 - 2005 Intel Corporation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program; if not, write to the Free Software Foundation, Inc., 59 + * Temple Place - Suite 330, Boston, MA 02111-1307, USA. + */ + +#ifndef _ATHL1E_HW_H_ +#define _ATHL1E_HW_H_ + +#include <linux/types.h> +#include <linux/mii.h> + +struct atl1e_adapter; +struct atl1e_hw; + +/* function prototype */ +s32 atl1e_reset_hw(struct atl1e_hw *hw); +s32 atl1e_read_mac_addr(struct atl1e_hw *hw); +s32 atl1e_init_hw(struct atl1e_hw *hw); +s32 atl1e_phy_commit(struct atl1e_hw *hw); +s32 atl1e_get_speed_and_duplex(struct atl1e_hw *hw, u16 *speed, u16 *duplex); +u32 atl1e_auto_get_fc(struct atl1e_adapter *adapter, u16 duplex); +u32 atl1e_hash_mc_addr(struct atl1e_hw *hw, u8 *mc_addr); +void atl1e_hash_set(struct atl1e_hw *hw, u32 hash_value); +s32 atl1e_read_phy_reg(struct atl1e_hw *hw, u16 reg_addr, u16 *phy_data); +s32 atl1e_write_phy_reg(struct atl1e_hw *hw, u32 reg_addr, u16 phy_data); +s32 atl1e_validate_mdi_setting(struct atl1e_hw *hw); +void atl1e_hw_set_mac_addr(struct atl1e_hw *hw); +bool atl1e_read_eeprom(struct atl1e_hw *hw, u32 offset, u32 *p_value); +bool atl1e_write_eeprom(struct atl1e_hw *hw, u32 offset, u32 value); +s32 atl1e_phy_enter_power_saving(struct atl1e_hw *hw); +s32 atl1e_phy_leave_power_saving(struct atl1e_hw *hw); +s32 atl1e_phy_init(struct atl1e_hw *hw); +int atl1e_check_eeprom_exist(struct atl1e_hw *hw); +void atl1e_force_ps(struct atl1e_hw *hw); +s32 atl1e_restart_autoneg(struct atl1e_hw *hw); + +/* register definition */ +#define REG_PM_CTRLSTAT 0x44 + +#define REG_PCIE_CAP_LIST 0x58 + +#define REG_DEVICE_CAP 0x5C +#define DEVICE_CAP_MAX_PAYLOAD_MASK 0x7 +#define DEVICE_CAP_MAX_PAYLOAD_SHIFT 0 + +#define REG_DEVICE_CTRL 0x60 +#define DEVICE_CTRL_MAX_PAYLOAD_MASK 0x7 +#define DEVICE_CTRL_MAX_PAYLOAD_SHIFT 5 +#define DEVICE_CTRL_MAX_RREQ_SZ_MASK 0x7 +#define DEVICE_CTRL_MAX_RREQ_SZ_SHIFT 12 + +#define REG_VPD_CAP 0x6C +#define VPD_CAP_ID_MASK 0xff +#define VPD_CAP_ID_SHIFT 0 +#define VPD_CAP_NEXT_PTR_MASK 0xFF +#define VPD_CAP_NEXT_PTR_SHIFT 8 +#define VPD_CAP_VPD_ADDR_MASK 0x7FFF +#define VPD_CAP_VPD_ADDR_SHIFT 16 +#define VPD_CAP_VPD_FLAG 0x80000000 + +#define REG_VPD_DATA 0x70 + +#define REG_SPI_FLASH_CTRL 0x200 +#define SPI_FLASH_CTRL_STS_NON_RDY 0x1 +#define SPI_FLASH_CTRL_STS_WEN 0x2 +#define SPI_FLASH_CTRL_STS_WPEN 0x80 +#define SPI_FLASH_CTRL_DEV_STS_MASK 0xFF +#define SPI_FLASH_CTRL_DEV_STS_SHIFT 0 +#define SPI_FLASH_CTRL_INS_MASK 0x7 +#define SPI_FLASH_CTRL_INS_SHIFT 8 +#define SPI_FLASH_CTRL_START 0x800 +#define SPI_FLASH_CTRL_EN_VPD 0x2000 +#define SPI_FLASH_CTRL_LDSTART 0x8000 +#define SPI_FLASH_CTRL_CS_HI_MASK 0x3 +#define SPI_FLASH_CTRL_CS_HI_SHIFT 16 +#define SPI_FLASH_CTRL_CS_HOLD_MASK 0x3 +#define SPI_FLASH_CTRL_CS_HOLD_SHIFT 18 +#define SPI_FLASH_CTRL_CLK_LO_MASK 0x3 +#define SPI_FLASH_CTRL_CLK_LO_SHIFT 20 +#define SPI_FLASH_CTRL_CLK_HI_MASK 0x3 +#define SPI_FLASH_CTRL_CLK_HI_SHIFT 22 +#define SPI_FLASH_CTRL_CS_SETUP_MASK 0x3 +#define SPI_FLASH_CTRL_CS_SETUP_SHIFT 24 +#define SPI_FLASH_CTRL_EROM_PGSZ_MASK 0x3 +#define SPI_FLASH_CTRL_EROM_PGSZ_SHIFT 26 +#define SPI_FLASH_CTRL_WAIT_READY 0x10000000 + +#define REG_SPI_ADDR 0x204 + +#define REG_SPI_DATA 0x208 + +#define REG_SPI_FLASH_CONFIG 0x20C +#define SPI_FLASH_CONFIG_LD_ADDR_MASK 0xFFFFFF +#define SPI_FLASH_CONFIG_LD_ADDR_SHIFT 0 +#define SPI_FLASH_CONFIG_VPD_ADDR_MASK 0x3 +#define SPI_FLASH_CONFIG_VPD_ADDR_SHIFT 24 +#define SPI_FLASH_CONFIG_LD_EXIST 0x4000000 + + +#define REG_SPI_FLASH_OP_PROGRAM 0x210 +#define REG_SPI_FLASH_OP_SC_ERASE 0x211 +#define REG_SPI_FLASH_OP_CHIP_ERASE 0x212 +#define REG_SPI_FLASH_OP_RDID 0x213 +#define REG_SPI_FLASH_OP_WREN 0x214 +#define REG_SPI_FLASH_OP_RDSR 0x215 +#define REG_SPI_FLASH_OP_WRSR 0x216 +#define REG_SPI_FLASH_OP_READ 0x217 + +#define REG_TWSI_CTRL 0x218 +#define TWSI_CTRL_LD_OFFSET_MASK 0xFF +#define TWSI_CTRL_LD_OFFSET_SHIFT 0 +#define TWSI_CTRL_LD_SLV_ADDR_MASK 0x7 +#define TWSI_CTRL_LD_SLV_ADDR_SHIFT 8 +#define TWSI_CTRL_SW_LDSTART 0x800 +#define TWSI_CTRL_HW_LDSTART 0x1000 +#define TWSI_CTRL_SMB_SLV_ADDR_MASK 0x0x7F +#define TWSI_CTRL_SMB_SLV_ADDR_SHIFT 15 +#define TWSI_CTRL_LD_EXIST 0x400000 +#define TWSI_CTRL_READ_FREQ_SEL_MASK 0x3 +#define TWSI_CTRL_READ_FREQ_SEL_SHIFT 23 +#define TWSI_CTRL_FREQ_SEL_100K 0 +#define TWSI_CTRL_FREQ_SEL_200K 1 +#define TWSI_CTRL_FREQ_SEL_300K 2 +#define TWSI_CTRL_FREQ_SEL_400K 3 +#define TWSI_CTRL_SMB_SLV_ADDR +#define TWSI_CTRL_WRITE_FREQ_SEL_MASK 0x3 +#define TWSI_CTRL_WRITE_FREQ_SEL_SHIFT 24 + + +#define REG_PCIE_DEV_MISC_CTRL 0x21C +#define PCIE_DEV_MISC_CTRL_EXT_PIPE 0x2 +#define PCIE_DEV_MISC_CTRL_RETRY_BUFDIS 0x1 +#define PCIE_DEV_MISC_CTRL_SPIROM_EXIST 0x4 +#define PCIE_DEV_MISC_CTRL_SERDES_ENDIAN 0x8 +#define PCIE_DEV_MISC_CTRL_SERDES_SEL_DIN 0x10 + +#define REG_PCIE_PHYMISC 0x1000 +#define PCIE_PHYMISC_FORCE_RCV_DET 0x4 + +#define REG_LTSSM_TEST_MODE 0x12FC +#define LTSSM_TEST_MODE_DEF 0xE000 + +/* Selene Master Control Register */ +#define REG_MASTER_CTRL 0x1400 +#define MASTER_CTRL_SOFT_RST 0x1 +#define MASTER_CTRL_MTIMER_EN 0x2 +#define MASTER_CTRL_ITIMER_EN 0x4 +#define MASTER_CTRL_MANUAL_INT 0x8 +#define MASTER_CTRL_ITIMER2_EN 0x20 +#define MASTER_CTRL_INT_RDCLR 0x40 +#define MASTER_CTRL_LED_MODE 0x200 +#define MASTER_CTRL_REV_NUM_SHIFT 16 +#define MASTER_CTRL_REV_NUM_MASK 0xff +#define MASTER_CTRL_DEV_ID_SHIFT 24 +#define MASTER_CTRL_DEV_ID_MASK 0xff + +/* Timer Initial Value Register */ +#define REG_MANUAL_TIMER_INIT 0x1404 + + +/* IRQ ModeratorTimer Initial Value Register */ +#define REG_IRQ_MODU_TIMER_INIT 0x1408 /* w */ +#define REG_IRQ_MODU_TIMER2_INIT 0x140A /* w */ + + +#define REG_GPHY_CTRL 0x140C +#define GPHY_CTRL_EXT_RESET 1 +#define GPHY_CTRL_PIPE_MOD 2 +#define GPHY_CTRL_TEST_MODE_MASK 3 +#define GPHY_CTRL_TEST_MODE_SHIFT 2 +#define GPHY_CTRL_BERT_START 0x10 +#define GPHY_CTRL_GATE_25M_EN 0x20 +#define GPHY_CTRL_LPW_EXIT 0x40 +#define GPHY_CTRL_PHY_IDDQ 0x80 +#define GPHY_CTRL_PHY_IDDQ_DIS 0x100 +#define GPHY_CTRL_PCLK_SEL_DIS 0x200 +#define GPHY_CTRL_HIB_EN 0x400 +#define GPHY_CTRL_HIB_PULSE 0x800 +#define GPHY_CTRL_SEL_ANA_RST 0x1000 +#define GPHY_CTRL_PHY_PLL_ON 0x2000 +#define GPHY_CTRL_PWDOWN_HW 0x4000 +#define GPHY_CTRL_DEFAULT (\ + GPHY_CTRL_PHY_PLL_ON |\ + GPHY_CTRL_SEL_ANA_RST |\ + GPHY_CTRL_HIB_PULSE |\ + GPHY_CTRL_HIB_EN) + +#define GPHY_CTRL_PW_WOL_DIS (\ + GPHY_CTRL_PHY_PLL_ON |\ + GPHY_CTRL_SEL_ANA_RST |\ + GPHY_CTRL_HIB_PULSE |\ + GPHY_CTRL_HIB_EN |\ + GPHY_CTRL_PWDOWN_HW |\ + GPHY_CTRL_PCLK_SEL_DIS |\ + GPHY_CTRL_PHY_IDDQ) + +/* IRQ Anti-Lost Timer Initial Value Register */ +#define REG_CMBDISDMA_TIMER 0x140E + + +/* Block IDLE Status Register */ +#define REG_IDLE_STATUS 0x1410 +#define IDLE_STATUS_RXMAC 1 /* 1: RXMAC state machine is in non-IDLE state. 0: RXMAC is idling */ +#define IDLE_STATUS_TXMAC 2 /* 1: TXMAC state machine is in non-IDLE state. 0: TXMAC is idling */ +#define IDLE_STATUS_RXQ 4 /* 1: RXQ state machine is in non-IDLE state. 0: RXQ is idling */ +#define IDLE_STATUS_TXQ 8 /* 1: TXQ state machine is in non-IDLE state. 0: TXQ is idling */ +#define IDLE_STATUS_DMAR 0x10 /* 1: DMAR state machine is in non-IDLE state. 0: DMAR is idling */ +#define IDLE_STATUS_DMAW 0x20 /* 1: DMAW state machine is in non-IDLE state. 0: DMAW is idling */ +#define IDLE_STATUS_SMB 0x40 /* 1: SMB state machine is in non-IDLE state. 0: SMB is idling */ +#define IDLE_STATUS_CMB 0x80 /* 1: CMB state machine is in non-IDLE state. 0: CMB is idling */ + +/* MDIO Control Register */ +#define REG_MDIO_CTRL 0x1414 +#define MDIO_DATA_MASK 0xffff /* On MDIO write, the 16-bit control data to write to PHY MII management register */ +#define MDIO_DATA_SHIFT 0 /* On MDIO read, the 16-bit status data that was read from the PHY MII management register*/ +#define MDIO_REG_ADDR_MASK 0x1f /* MDIO register address */ +#define MDIO_REG_ADDR_SHIFT 16 +#define MDIO_RW 0x200000 /* 1: read, 0: write */ +#define MDIO_SUP_PREAMBLE 0x400000 /* Suppress preamble */ +#define MDIO_START 0x800000 /* Write 1 to initiate the MDIO master. And this bit is self cleared after one cycle*/ +#define MDIO_CLK_SEL_SHIFT 24 +#define MDIO_CLK_25_4 0 +#define MDIO_CLK_25_6 2 +#define MDIO_CLK_25_8 3 +#define MDIO_CLK_25_10 4 +#define MDIO_CLK_25_14 5 +#define MDIO_CLK_25_20 6 +#define MDIO_CLK_25_28 7 +#define MDIO_BUSY 0x8000000 +#define MDIO_AP_EN 0x10000000 +#define MDIO_WAIT_TIMES 10 + +/* MII PHY Status Register */ +#define REG_PHY_STATUS 0x1418 +#define PHY_STATUS_100M 0x20000 +#define PHY_STATUS_EMI_CA 0x40000 + +/* BIST Control and Status Register0 (for the Packet Memory) */ +#define REG_BIST0_CTRL 0x141c +#define BIST0_NOW 0x1 /* 1: To trigger BIST0 logic. This bit stays high during the */ +/* BIST process and reset to zero when BIST is done */ +#define BIST0_SRAM_FAIL 0x2 /* 1: The SRAM failure is un-repairable because it has address */ +/* decoder failure or more than 1 cell stuck-to-x failure */ +#define BIST0_FUSE_FLAG 0x4 /* 1: Indicating one cell has been fixed */ + +/* BIST Control and Status Register1(for the retry buffer of PCI Express) */ +#define REG_BIST1_CTRL 0x1420 +#define BIST1_NOW 0x1 /* 1: To trigger BIST0 logic. This bit stays high during the */ +/* BIST process and reset to zero when BIST is done */ +#define BIST1_SRAM_FAIL 0x2 /* 1: The SRAM failure is un-repairable because it has address */ +/* decoder failure or more than 1 cell stuck-to-x failure.*/ +#define BIST1_FUSE_FLAG 0x4 + +/* SerDes Lock Detect Control and Status Register */ +#define REG_SERDES_LOCK 0x1424 +#define SERDES_LOCK_DETECT 1 /* 1: SerDes lock detected . This signal comes from Analog SerDes */ +#define SERDES_LOCK_DETECT_EN 2 /* 1: Enable SerDes Lock detect function */ + +/* MAC Control Register */ +#define REG_MAC_CTRL 0x1480 +#define MAC_CTRL_TX_EN 1 /* 1: Transmit Enable */ +#define MAC_CTRL_RX_EN 2 /* 1: Receive Enable */ +#define MAC_CTRL_TX_FLOW 4 /* 1: Transmit Flow Control Enable */ +#define MAC_CTRL_RX_FLOW 8 /* 1: Receive Flow Control Enable */ +#define MAC_CTRL_LOOPBACK 0x10 /* 1: Loop back at G/MII Interface */ +#define MAC_CTRL_DUPLX 0x20 /* 1: Full-duplex mode 0: Half-duplex mode */ +#define MAC_CTRL_ADD_CRC 0x40 /* 1: Instruct MAC to attach CRC on all egress Ethernet frames */ +#define MAC_CTRL_PAD 0x80 /* 1: Instruct MAC to pad short frames to 60-bytes, and then attach CRC. This bit has higher priority over CRC_EN */ +#define MAC_CTRL_LENCHK
|
Pages: 1 Prev: bcm203x bluetooth dongle does not work Next: What to do with `kswapd0: page allocation failure. ` ? |