From: ramswell on
On Nov 11, 2:20 pm, Colin J Thomson <coli...(a)nospam.gmail.com> wrote:
> Joseph Fenn wrote:
> >> Not true.. my RamLink came from CMD ~5 years before Maurice took over and
> >> it had the timing cable supplied with it,
> >> On a side note if you have a SCPU + RL combo there is a good chance its
> >> not needed. I have two 128D's here one needs the cable one does not.
> > I beg to differ with you Colin. I also had my intial R/L long before
> > Maurice took over at last longer than you say 5 years. It had no
> > such wires to plug in anywhere. Those 2 wires on the last versions
> > of R/L after Maurice took over were for timeing control.
>
> Well I guess I was lucky or maybe because I live a few thousand miles away
> they sent me one :) Its a single wire with a tiny "clip on" probe at one
> end and a header type plug on the other end that plugs into the RL, look up
> the end of the RL and you will see two pins for the header plug to connect
> to.
>
> Anyway my RL is faulty, so it needs to get fixed :(
>
> Cheers
>
> Colin



Yep. That's it! ;)

Charles

From: the.glenn0r on
Thanks for the help. :)
I'm going to bid on that ebay auction first. Hope I get it.
If not I'll try some soldering ..

The CMD Ramlink user manual I have is a 4th edition dated February
1993.
And it clearly states that you must have a jumper cable on a C64 or
C128D.

Glenn

From: Hernan Vergara on
Hi Joseph and Colin,

I beg to differ with you Joseph, Colin is correct. :-)

Hernan.


On Sun, 11 Nov 2007, Joseph Fenn wrote:

>
>
> >
> > Not true.. my RamLink came from CMD ~5 years before Maurice took over and it
> > had the timing cable supplied with it,
> > On a side note if you have a SCPU + RL combo there is a good chance its not
> > needed. I have two 128D's here one needs the cable one does not.
> >
> > -Colin
> >
> I beg to differ with you Colin. I also had my intial R/L long before
> Maurice took over at last longer than you say 5 years. It had no
> such wires to plug in anywhere. Those 2 wires on the last versions
> of R/L after Maurice took over were for timeing control.
> Joe
>
>
From: ramswell on
On Nov 9, 5:48 pm, the.glen...(a)heimplass.no wrote:
> Hello.
> 2-3 weeks ago I got CMD RamLink (RL) with 4 mb.
> My problem : it's missing a jumper clip cable. It's supposed to
> be connected from the RL to a pin on the C64 motherboard - This is
> needed on
> C64 and C128D for ( quote from the manual ) 'Proper timing operations
> with the RL'.
> The manual further states that this kind of connection is not
> necessary with a C128.
>
> But I only have a C64 and a C128D.
>
> As the RL works now I only get to the RL Jiffydos basic screen and
> when I try to
> load the dir from the RL I only get errors or device not present.
>
> So I have to build me a jumper clip cable. But I dont know how the
> cable looks like.
> Any instructions on how to do this would be helpful ...
>
> Glenn



I just found my "SPARE" this morning if you're interested in it. All
I want it $5.00 + S&H for a TOTAL of $7 in the Continental US.


Charles
From: Mike Paull on
On Sat, 10 Nov 2007 09:30:23 -1000, Joseph Fenn <jfenn(a)lava.net> wrote:

>See me previous followup on this question. The original CMD
>ramlinks had no jumper cables at all. They were later added after
>Maurice took control of the product. They were for timeing control
>which apparently was unneccessary on the old versions.
> Joe
>

Sorry Joe, your dates are a little mixed up there. Maurice purchased the
right to manufacture and existings stocks from CMD in 2001. My Ramlink
manual which is dated 1993 has instructions for attaching the timing clip.
So the Rev.2 Ramlink obviously pre-dates Maurices purchasing of CMD.

For the original poster, making a clip is easy. Go to almost any
electronics store and buy a two pin header socket, a small length of thin
guage hookup wire about 150mm long and an IC Clip.

The two pin header only needs one pin to have the wire connected to it and
on my Ramlink, it doesn't matter which one as they are connected together
internally. So strip a bit of plastic off the hookup wire and expose the
copper, slide inside one of the two metal header socket connectors and
crimp with your favourite pair of pliers! The IC socket will likely have a
similar crimping arrangement so do that for the other end of the wire.

Simple as that, should cost you all of about $1.50 and five minutes of your
time :)

Mike