Prev: Mike J. Henry of Basement Boys Software
Next: Ok ladies.. Now that I have a SuperCPU, sell me your CMD HD!!
From: the.glenn0r on 9 Nov 2007 20:48
Hello.
2-3 weeks ago I got CMD RamLink (RL) with 4 mb.
My problem : it's missing a jumper clip cable. It's supposed to
be connected from the RL to a pin on the C64 motherboard - This is
needed on
C64 and C128D for ( quote from the manual ) 'Proper timing operations
with the RL'.
The manual further states that this kind of connection is not
necessary with a C128.

But I only have a C64 and a C128D.

As the RL works now I only get to the RL Jiffydos basic screen and
when I try to
load the dir from the RL I only get errors or device not present.

So I have to build me a jumper clip cable. But I dont know how the
cable looks like.
Any instructions on how to do this would be helpful ...

Glenn

From: ramswell on 9 Nov 2007 21:36
On Nov 9, 5:48 pm, the.glen...(a)heimplass.no wrote:
> Hello.
> 2-3 weeks ago I got CMD RamLink (RL) with 4 mb.
> My problem : it's missing a jumper clip cable. It's supposed to
> be connected from the RL to a pin on the C64 motherboard - This is
> needed on
> C64 and C128D for ( quote from the manual ) 'Proper timing operations
> with the RL'.
> The manual further states that this kind of connection is not
> necessary with a C128.
>
> But I only have a C64 and a C128D.
>
> As the RL works now I only get to the RL Jiffydos basic screen and
> when I try to
> load the dir from the RL I only get errors or device not present.
>
> So I have to build me a jumper clip cable. But I dont know how the
> cable looks like.
> Any instructions on how to do this would be helpful ...
>
> Glenn



Well what I can tell you is to to go to Radio Shack and buy a pack of
jumper clips for $5.00 and then get a hold of a "PC MINI FAN" and CUT
OFF the end of the wire (this is the end that will connect to one end
of the Jumper wires that you buy from radio shack.
Then connect the fan end to one end (an end that you will cut off the
jumper wire) of the jumper wire and WHALLAH! There ya go!

And if I remember correctly, I "believe" that the jumper wire will
plug into the RL with the "fan" end and the "jumper clip" end will
clip onto resistor #47 (correct me if I'm wrong people).

Good luck and let us know how it turns out for you....


Charles> 8-Bit Designs


From: Payton Byrd on 9 Nov 2007 23:47


<the.glenn0r(a)heimplass.no> wrote in message
news:1194659315.507809.120600(a)19g2000hsx.googlegroups.com...
> Hello.
> 2-3 weeks ago I got CMD RamLink (RL) with 4 mb.
> My problem : it's missing a jumper clip cable. It's supposed to
> be connected from the RL to a pin on the C64 motherboard - This is
> needed on
> C64 and C128D for ( quote from the manual ) 'Proper timing operations
> with the RL'.
> The manual further states that this kind of connection is not
> necessary with a C128.
>
> But I only have a C64 and a C128D.
>

My RL works fine on my 128D without the jumper clip. I think it's dependent
on the revision of your RL.

From: Dragos on 10 Nov 2007 01:06
WHALLAH ??????


Perhaps you meant: Voila or specifically Voilà!


From: Payton Byrd on 10 Nov 2007 05:36


"Dragos" <mgladson(a)gmail.com> wrote in message
news:1194674801.063982.275540(a)22g2000hsm.googlegroups.com...
> WHALLAH ??????
>
>
> Perhaps you meant: Voila or specifically Voil�!
>
>

Who were you replying to?

 |  Next  |  Last
Pages: 1 2 3 4 5 6
Prev: Mike J. Henry of Basement Boys Software
Next: Ok ladies.. Now that I have a SuperCPU, sell me your CMD HD!!