From: Uwe Hercksen on


Ken S. Tucker schrieb:

> I need to use very fine 120V wire (like magnetic wire),
> the model uses 8# test monofilament right now and weighs
> 1/2 # , but a strong wind requires that 8# test.
> Is there a table that gives wire gauge & tensile strength?
> The current will likely be a max of 1/2 amp.

Hello,

you might need a combination of steel wire for tensile strength and
copper wire for low resistance to the electric current. To keep the
weight low, replace copper with aluminium.

Bye

From: Ken S. Tucker on
On Aug 2, 2:13 am, Uwe Hercksen <herck...(a)mew.uni-erlangen.de> wrote:
> Ken S. Tucker schrieb:
>
> > I need to use very fine 120V wire (like magnetic wire),
> > the model uses 8# test monofilament right now and weighs
> > 1/2 # , but a strong wind requires that 8# test.
> > Is there a table that gives wire gauge & tensile strength?
> > The current will likely be a max of 1/2 amp.
>
> Hello,
> you might need a combination of steel wire for tensile strength and
> copper wire for low resistance to the electric current. To keep the
> weight low, replace copper with aluminium.
> Bye

Hi
We did an experiment yesterday, we connected a AWG 36 wire
in series with a 100W bulb, dimmer and Current meter.
(The AWG 36 wire was carefully wrapped around a couple of
3/16" bolts and carefully snugged with nuts, a poor man's fuse).

As we turned up the dimmer we expected the wire to fuse but it
didn't, it took the full current supplying a 100W bulb, I kid you not,
that's about 0.9 amps!
We got the wire from unwrapping a reed switch and checked the
gauge twice by tensile strength.
I invite anyone else to try the experiment.
Regards
Ken

From: Dirk Bruere at NeoPax on
On 02/08/2010 17:47, Ken S. Tucker wrote:
> On Aug 2, 2:13 am, Uwe Hercksen<herck...(a)mew.uni-erlangen.de> wrote:
>> Ken S. Tucker schrieb:
>>
>>> I need to use very fine 120V wire (like magnetic wire),
>>> the model uses 8# test monofilament right now and weighs
>>> 1/2 # , but a strong wind requires that 8# test.
>>> Is there a table that gives wire gauge& tensile strength?
>>> The current will likely be a max of 1/2 amp.
>>
>> Hello,
>> you might need a combination of steel wire for tensile strength and
>> copper wire for low resistance to the electric current. To keep the
>> weight low, replace copper with aluminium.
>> Bye
>
> Hi
> We did an experiment yesterday, we connected a AWG 36 wire
> in series with a 100W bulb, dimmer and Current meter.
> (The AWG 36 wire was carefully wrapped around a couple of
> 3/16" bolts and carefully snugged with nuts, a poor man's fuse).
>
> As we turned up the dimmer we expected the wire to fuse but it
> didn't, it took the full current supplying a 100W bulb, I kid you not,
> that's about 0.9 amps!
> We got the wire from unwrapping a reed switch and checked the
> gauge twice by tensile strength.
> I invite anyone else to try the experiment.
> Regards
> Ken
>

If you're brave, try it with carbon fibre.


--
Dirk

http://www.transcendence.me.uk/ - Transcendence UK
http://www.blogtalkradio.com/onetribe - Occult Talk Show
From: Nunya on
On Aug 2, 3:14 pm, Dirk Bruere at NeoPax <dirk.bru...(a)gmail.com>
wrote:
> On 02/08/2010 17:47, Ken S. Tucker wrote:
>
>
>
> > On Aug 2, 2:13 am, Uwe Hercksen<herck...(a)mew.uni-erlangen.de>  wrote:
> >> Ken S. Tucker schrieb:
>
> >>> I need to use very fine 120V wire (like magnetic wire),
> >>> the model uses 8# test monofilament right now and weighs
> >>> 1/2 # , but a strong wind requires that 8# test.
> >>> Is there a table that gives wire gauge&  tensile strength?
> >>> The current will likely be a max of 1/2 amp.
>
> >> Hello,
> >> you might need a combination of steel wire for tensile strength and
> >> copper wire for low resistance to the electric current. To keep the
> >> weight low, replace copper with aluminium.
> >> Bye
>
> > Hi
> > We did an experiment yesterday, we connected a AWG 36 wire
> > in series with a 100W bulb, dimmer and Current meter.
> > (The AWG 36 wire was carefully wrapped around a couple of
> > 3/16" bolts and carefully snugged with nuts, a poor man's fuse).
>
> > As we turned up the dimmer we expected the wire to fuse but it
> > didn't, it took the full current supplying a 100W bulb, I kid you not,
> > that's about 0.9 amps!
> > We got the wire from unwrapping a reed switch and checked the
> > gauge twice by tensile strength.
> > I invite anyone else to try the experiment.
> > Regards
> > Ken
>
> If you're brave, try it with carbon fibre.
>
> --
> Dirk
>
> http://www.transcendence.me.uk/- Transcendence UKhttp://www.blogtalkradio..com/onetribe- Occult Talk Show

Silk strands with old fashioned Bell wire "ribbon wrap".

They probably use Rayon. Remember that wire?
Also used for speaker coil attach wires.
From: Uwe Hercksen on


Ken S. Tucker schrieb:

> As we turned up the dimmer we expected the wire to fuse but it
> didn't, it took the full current supplying a 100W bulb, I kid you not,
> that's about 0.9 amps!

Hello,

a thin wire is able to carry a high current if it is well cooled. But
you will loose some voltage.

Bye