Prev: Plasma service manuals, no PS or syscon schematics?
Next: tektronix 2467
From: JW on 15 Jun 2007 06:24
I am looking for some vintage AC power cords for older HP test equipment.
I have a number of pieces of test equipment, and only one power cord. The
only marking on it is "Electricord". It is a three conductor cord that
uses three round female sockets on the end that terminates at the
equipment, and is similar to the old power cords that were found on coffee
pots and such (but with one more pin in the center offset from the other
two - a ground, I suppose). I believe it is typical of HP equipment made
in the 1960's to have these, such as the HP745A AC calibrator, among
others. Does anyone know where I might find some of these, or perhaps know
what the original HP part # is? (I know that I could hard-wire a standard
line cord to these units, but would much rather have the proper cords.)

Thanks!
From: Lee Richardson on 15 Jun 2007 07:19
If they are the same ones used on old electromechanical Victor and Burroughs
adding machines, I have those in stock. Send e-mail to
mechtech(a)evansville.net .

Lee Richardson
Evansville, Indiana


"JW" <none(a)dev.nul> wrote in message
news:e1p4735r8j48l8gibsnl1039inmed71ch8(a)4ax.com...
>I am looking for some vintage AC power cords for older HP test equipment.
> I have a number of pieces of test equipment, and only one power cord. The
> only marking on it is "Electricord". It is a three conductor cord that
> uses three round female sockets on the end that terminates at the
> equipment, and is similar to the old power cords that were found on coffee
> pots and such (but with one more pin in the center offset from the other
> two - a ground, I suppose). I believe it is typical of HP equipment made
> in the 1960's to have these, such as the HP745A AC calibrator, among
> others. Does anyone know where I might find some of these, or perhaps know
> what the original HP part # is? (I know that I could hard-wire a standard
> line cord to these units, but would much rather have the proper cords.)
>
> Thanks!


From: Michael A. Terrell on 15 Jun 2007 07:33
Lee Richardson wrote:
>
> If they are the same ones used on old electromechanical Victor and Burroughs
> adding machines, I have those in stock. Send e-mail to
> mechtech(a)evansville.net .


Be aware that there are two different pinouts on these cables.


--
Service to my country? Been there, Done that, and I've got my DD214 to
prove it.
Member of DAV #85.

Michael A. Terrell
Central Florida
From: Lee Richardson on 15 Jun 2007 08:53
Good morning.
On these, when looking at the hole end with the center hole towards the top,
left hole is hot (black wire), center hole is grounding (green wire), and
the right hole is grounded or neutral (white wire).

Thanks,
Lee Richardson
Mech-Tech


"Michael A. Terrell" <mike.terrell(a)earthlink.net> wrote in message
news:46727939.4FAFA08C(a)earthlink.net...
> Lee Richardson wrote:
>>
>> If they are the same ones used on old electromechanical Victor and
>> Burroughs
>> adding machines, I have those in stock. Send e-mail to
>> mechtech(a)evansville.net .
>
>
> Be aware that there are two different pinouts on these cables.
>
>
> --
> Service to my country? Been there, Done that, and I've got my DD214 to
> prove it.
> Member of DAV #85.
>
> Michael A. Terrell
> Central Florida


From: JW on 15 Jun 2007 08:57
On Fri, 15 Jun 2007 06:19:21 -0500 "Lee Richardson"
<mechtech(a)evansville.net> wrote in Message id:
<ho-dnbVQG5pU6O_bnZ2dnUVZ_gKdnZ2d(a)sigecom.net>:

>If they are the same ones used on old electromechanical Victor and Burroughs
>adding machines,

Hello Lee,

Jeez, I don't know. Do they look like this?:
http://home.comcast.net/~66gtojayw/linecord.jpg

Also, is the center conductor ground, or can it be re-wired if not? (Not
molded)

>I have those in stock. Send e-mail to
>mechtech(a)evansville.net .

How many do you have and how much are you asking for them?

Thanks!
 |  Next  |  Last
Pages: 1 2 3 4
Prev: Plasma service manuals, no PS or syscon schematics?
Next: tektronix 2467