Cisco

Vista Smart Security virus (fake program)
Vista smart security is a rogue spyware fake program. do not trust vista smart security as its a scam virus asking for money to buy its license. instead of paying for vista smart security, remove vista smart security virus off your pc. to remove it manually or by using an antispyware program, see the vista smart se... 23 Apr 2010 20:39

BGP redistribute route-map question.
------- I have a customer that has the config below. I would never write it like this, and use a standard ACL or distribute list instead. but to my surprise, this is allowing every static route to go be advertised.. I would think that "permit ip host 0.0.0.0 host 0.0.0.0" would get no matches and that the expl... 30 Apr 2010 00:45

How can you get an incomplete ARP?
On Apr 21, 1:42 pm, Rob <nom...(a)example.com> wrote: crzzy1<cozz...(a)hotmail.com> wrote: Perhaps someone can put this into perspective for me. This is an age old question that has arisen many times throughout the years and my web searches have failed to answer this. The host is visible in arp an... 23 Apr 2010 17:25

Vista Smart Security virus (fake program)
darfun <darfun.inc(a)gmail.com> wrote: Vista smart security is a rogue spyware fake program. do not trust Do not trust darfun.. He is a spamming nitwit. ... 23 Apr 2010 17:25

3560 Limit rate port
Can any describe a simple method to rate limit a fastethernet on a 3560 - I have seen and tried Police , srr queue commands but I have only been anle to achieve the desired rate limit on the inside of the port - it appears to still use the full bandwidth on its egress side. ! ! policy-map POLICY_5Mb class CLA... 27 Apr 2010 13:18

Failover problem with Firewall Service Modul (FWSM) Catalyst 6500
I have set up two FWSM in Active/Standby Failover with Stateful Failover and State Link in multiple context mode. The switches run IOS 12.2.33-SXI3 and the FWSM version 4.0(11). When I enable failover, the active unit sends the configuration to the standby FWSM. Now my problem: all dhcp-server commands beginnin... 23 Apr 2010 17:24

4900 switch config via CNA (seriously)
I know , I know, but I've been bored and wanted to play with CNA. The latest version I have only seems to have a template for CE520. Supposedly 4900 are supported also but I can't get it to work. I made one of the 4948 ports L3 and can ping it from laptop that has CNA installed and still can't get in. Is there a 49... 20 Apr 2010 15:42

Pix ACLs
Hello, the pix/asa above 7.x can filter on egress and igress but what is the drawback with filtering just egress-only? (if you have more interfaces igress and egress filter is imho a pain) CL ... 20 Apr 2010 15:42

c1811 isr dual nat
I've got a situation where i need the c1811 isr to do dual nat to two different external ip addresses to the same internal ip address - like below: ip nat inside sourse static 192.168.1.1 <outside address 1> ip nat inside source static 192.168.1.1 <outside address 2> this is because the 1811 is going behind... 15 Apr 2010 10:14

BRI interfaces status check
Hello, I need to check the status of the BRI interfaces from all of the routers on our network. I have to check it everyday to see which one is active. Is there any utility that performs such a task? Do I have to enable SNMP on the routers and would the network performance be affected by this move? Thanks a ... 24 Apr 2010 07:11