How to solder to solar panels.
in [Design]
|
Prev: What XTAL OSC is this?
Next: Moto 68HC11 dev kit
From: Archimedes' Lever on 3 May 2010 08:53 On Mon, 3 May 2010 13:02:31 +0100, "Nial Stewart" <nial*REMOVE_THIS*@nialstewartdevelopments.co.uk> wrote: >> I think 950F should've been more than enough.. It didn't even touch it. It simply just puddled >> and rolled off. > >What the base material? > >If the panel is acting as a massive thermal sink then you could be heating >the solder to 950 while the panel's getting nowhere near that. > >You could try pre-heating a corner with a blow torch (as long as this isn't >going to destroy the panel). > > >Nial. > When are the total retards and totally retarded suggestions in this group ever going to end!?
From: George Jefferson on 3 May 2010 12:54 "Archimedes' Lever" <OneBigLever(a)InfiniteSeries.Org> wrote in message news:3ohtt59bi5n1d6lblmpgq31m5ghb9ihdpi(a)4ax.com... > On Mon, 3 May 2010 13:02:31 +0100, "Nial Stewart" > <nial*REMOVE_THIS*@nialstewartdevelopments.co.uk> wrote: > >>> I think 950F should've been more than enough.. It didn't even touch it. >>> It simply just puddled >>> and rolled off. >> >>What the base material? >> >>If the panel is acting as a massive thermal sink then you could be heating >>the solder to 950 while the panel's getting nowhere near that. >> >>You could try pre-heating a corner with a blow torch (as long as this >>isn't >>going to destroy the panel). >> >> >>Nial. >> > When are the total retards and totally retarded suggestions in this > group ever going to end!? When you stop posting?
From: Archimedes' Lever on 22 May 2010 13:42 On Mon, 3 May 2010 11:54:01 -0500, "George Jefferson" <phreon111(a)gmail.com> wrote: > > >"Archimedes' Lever" <OneBigLever(a)InfiniteSeries.Org> wrote in message >news:3ohtt59bi5n1d6lblmpgq31m5ghb9ihdpi(a)4ax.com... >> On Mon, 3 May 2010 13:02:31 +0100, "Nial Stewart" >> <nial*REMOVE_THIS*@nialstewartdevelopments.co.uk> wrote: >> >>>> I think 950F should've been more than enough.. It didn't even touch it. >>>> It simply just puddled >>>> and rolled off. >>> >>>What the base material? >>> >>>If the panel is acting as a massive thermal sink then you could be heating >>>the solder to 950 while the panel's getting nowhere near that. >>> >>>You could try pre-heating a corner with a blow torch (as long as this >>>isn't >>>going to destroy the panel). >>> >>> >>>Nial. >>> >> When are the total retards and totally retarded suggestions in this >> group ever going to end!? > >When you stop posting? > > Youre IQ dropped 20 points the moment your sent that retarded post. Wait! It was already that low!
From: Archimedes' Lever on 22 May 2010 14:00 On Mon, 3 May 2010 11:54:01 -0500, "George Jefferson" <phreon111(a)gmail.com> wrote: > > >"Archimedes' Lever" <OneBigLever(a)InfiniteSeries.Org> wrote in message >news:3ohtt59bi5n1d6lblmpgq31m5ghb9ihdpi(a)4ax.com... >> On Mon, 3 May 2010 13:02:31 +0100, "Nial Stewart" >> <nial*REMOVE_THIS*@nialstewartdevelopments.co.uk> wrote: >> >>>> I think 950F should've been more than enough.. It didn't even touch it. >>>> It simply just puddled >>>> and rolled off. >>> >>>What the base material? >>> >>>If the panel is acting as a massive thermal sink then you could be heating >>>the solder to 950 while the panel's getting nowhere near that. >>> >>>You could try pre-heating a corner with a blow torch (as long as this >>>isn't >>>going to destroy the panel). >>> >>> >>>Nial. >>> >> When are the total retards and totally retarded suggestions in this >> group ever going to end!? > >When you stop posting? > > The proper attachment media is electrically conductive epoxy (silver filled), just like in the IC chip bonding industry, you retarded twit.
From: John Larkin on 22 May 2010 14:01
On Sat, 22 May 2010 10:42:49 -0700, Archimedes' Lever <OneBigLever(a)InfiniteSeries.Org> wrote: >On Mon, 3 May 2010 11:54:01 -0500, "George Jefferson" ><phreon111(a)gmail.com> wrote: > >> >> >>"Archimedes' Lever" <OneBigLever(a)InfiniteSeries.Org> wrote in message >>news:3ohtt59bi5n1d6lblmpgq31m5ghb9ihdpi(a)4ax.com... >>> On Mon, 3 May 2010 13:02:31 +0100, "Nial Stewart" >>> <nial*REMOVE_THIS*@nialstewartdevelopments.co.uk> wrote: >>> >>>>> I think 950F should've been more than enough.. It didn't even touch it. >>>>> It simply just puddled >>>>> and rolled off. >>>> >>>>What the base material? >>>> >>>>If the panel is acting as a massive thermal sink then you could be heating >>>>the solder to 950 while the panel's getting nowhere near that. >>>> >>>>You could try pre-heating a corner with a blow torch (as long as this >>>>isn't >>>>going to destroy the panel). >>>> >>>> >>>>Nial. >>>> >>> When are the total retards and totally retarded suggestions in this >>> group ever going to end!? >> >>When you stop posting? >> >> > Youre IQ dropped 20 points the moment your sent that retarded post. Youre? > > Wait! It was already that low! Think about that statement. You never were a math whiz. John |