From: krw on
On Sat, 17 Jul 2010 09:11:49 -0700, Joerg <invalid(a)invalid.invalid> wrote:

>krw(a)att.bizzzzzzzzzzzz wrote:
>> On Sat, 17 Jul 2010 06:33:23 -0700, Joerg <invalid(a)invalid.invalid> wrote:
>>
>>> Frank Buss wrote:
>>>> Joerg wrote:
>>>>
>>>>> I believe Newark carries them.
>>>> Digikey has it, too. Search for "keystone test points" and you'll get a
>>>> nice selection for diameter, color etc. Looks like it is popular, because
>>>> some types are available in container quantities :-)
>>>>
>>>> http://search.digikey.com/scripts/DkSearch/dksus.dll?Detail&name=5002K-ND
>>>>
>>> Thanks, I didn't know they carried these. Unfortunately such test points
>>> are comparatively large, for 0.040" holes and similar.
>>
>> Come on Joerg. They're only three for ten bucks. You can afford them!
>>
>> <yikes!> BTW, we use something similar for less than $.10 each. ...and those
>> are usually deleted when production settles down.
>
>
>I didn't say I can't afford them :-)

;-)

>They are just a bit large for modern SMT layouts. Technologically a bit
>long in the tooth.

We use them on power supplies and a couple of communications lines (RS-422).
They're useful for scope grounds.

There once were connectors that would accept a scope tip. Has anyone seen
those recently? They were *expensive* but for test jigs they would be useful.
From: Joerg on
krw(a)att.bizzzzzzzzzzzz wrote:
> On Sat, 17 Jul 2010 09:11:49 -0700, Joerg <invalid(a)invalid.invalid> wrote:
>
>> krw(a)att.bizzzzzzzzzzzz wrote:
>>> On Sat, 17 Jul 2010 06:33:23 -0700, Joerg <invalid(a)invalid.invalid> wrote:
>>>
>>>> Frank Buss wrote:
>>>>> Joerg wrote:
>>>>>
>>>>>> I believe Newark carries them.
>>>>> Digikey has it, too. Search for "keystone test points" and you'll get a
>>>>> nice selection for diameter, color etc. Looks like it is popular, because
>>>>> some types are available in container quantities :-)
>>>>>
>>>>> http://search.digikey.com/scripts/DkSearch/dksus.dll?Detail&name=5002K-ND
>>>>>
>>>> Thanks, I didn't know they carried these. Unfortunately such test points
>>>> are comparatively large, for 0.040" holes and similar.
>>> Come on Joerg. They're only three for ten bucks. You can afford them!
>>>
>>> <yikes!> BTW, we use something similar for less than $.10 each. ...and those
>>> are usually deleted when production settles down.
>>
>> I didn't say I can't afford them :-)
>
> ;-)
>
>> They are just a bit large for modern SMT layouts. Technologically a bit
>> long in the tooth.
>
> We use them on power supplies and a couple of communications lines (RS-422).
> They're useful for scope grounds.
>
> There once were connectors that would accept a scope tip. Has anyone seen
> those recently? They were *expensive* but for test jigs they would be useful.


Not recently. I often use needles, the ones that come with higher end
shirts. You know, where Murphy says that you'll always forget one when
trying it on and ... OUCH. Many can be soldered to (not all) and then
occasionally I use a rubber band to tug a bit on the cable or the needle
so it won't fly out.

The needles are free, as long as you pay the $49 plus tax for the shirt :-)

--
Regards, Joerg

http://www.analogconsultants.com/

"gmail" domain blocked because of excessive spam.
Use another domain or send PM.
From: Spehro Pefhany on
On Sat, 17 Jul 2010 06:02:00 +0200, the renowned Frank Buss
<fb(a)frank-buss.de> wrote:

>Joerg wrote:
>
>> I believe Newark carries them.
>
>Digikey has it, too. Search for "keystone test points" and you'll get a
>nice selection for diameter, color etc. Looks like it is popular, because
>some types are available in container quantities :-)

You mean a Tupperware container? ;-)

128,000 of those, bagged in 1K lots, is probably a bit under 10 lb (4
kg)


>http://search.digikey.com/scripts/DkSearch/dksus.dll?Detail&name=5002K-ND


Best regards,
Spehro Pefhany
--
"it's the network..." "The Journey is the reward"
speff(a)interlog.com Info for manufacturers: http://www.trexon.com
Embedded software/hardware/analog Info for designers: http://www.speff.com
From: Frank Buss on
Joerg wrote:

> Not recently. I often use needles, the ones that come with higher end
> shirts. You know, where Murphy says that you'll always forget one when
> trying it on and ... OUCH. Many can be soldered to (not all) and then
> occasionally I use a rubber band to tug a bit on the cable or the needle
> so it won't fly out.

I have some coils of silver coated copper. 1 mm diameter are nice for
soldering stable test points and 0.4 mm is useful, if you don't have much
space (or for dead bug style prototyping). Of course, not as easy and good
as a ready made test points with a loop and plastic ring for easier
mounting.

--
Frank Buss, fb(a)frank-buss.de
http://www.frank-buss.de, http://www.it4-systems.de
From: Frank Buss on
Spehro Pefhany wrote:

> You mean a Tupperware container? ;-)
>
> 128,000 of those, bagged in 1K lots, is probably a bit under 10 lb (4
> kg)

you are right, it is easy for me to be wrong when estimating volumens
without calculating :-)

--
Frank Buss, fb(a)frank-buss.de
http://www.frank-buss.de, http://www.it4-systems.de