Programming Failed
in [FPGA]
|
Prev: Solved! Why my pins were being optimized out. How do I get the firmware running now....
Next: E1 clock problem with Spartan3e...
From: salquraish on 11 Jan 2010 06:21 I am using JTAG parallel cable to program FPGA, while programming the FPGA code into the internal flash power was disconnected and finally "PROGRAM FAILED" message was observed. I had tried to program several times but still not able to program. The observed log is below, please find it. INFO:iMPACT - Current time: Fri Jan 8 21:38:55 2010 // *** BATCH CMD : Program -p 1 -e -v PROGRESS_START - Starting Operation. Maximum TCK operating frequency for this device chain: 10000000. Validating chain... Boundary-scan chain validated successfully. '1': SPI access core not detected. SPI access core will be downloaded to the device to enable operations. INFO:iMPACT - Downloading core file C:/Xilinx/11.1/ProgrammingTools/spartan3a/data/xc3s200an_spi.cor. '1': Downloading core... done. '1': Reading status register contents... CRC error : 0 IDCODE not validated while writing FDRI : 0 DCM Locked : 1 status of GTS_CFG_B : 1 status of GWE : 1 status of GHIGH : 1 value of VSEL pin 0 : 1 value of VSEL pin 1 : 1 value of VSEL pin 2 : 1 value of MODE pin M0 : 1 value of MODE pin M1 : 1 value of MODE pin M2 : 0 value of CFG_RDY (INIT_B) : 1 DONEIN input from Done Pin : 1 SYNC word not found : 0 INFO:iMPACT:2219 - Status register values: INFO:iMPACT - 0011 1111 1110 1100 INFO:iMPACT:2492 - '1': Completed downloading core to device. INFO:iMPACT - '1': Checking done pin....done. '1': Core downloaded successfully. INFO:iMPACT - Address 0x00000000 is in sector 0. INFO:iMPACT - Start block = 0 for address 0x00000000. INFO:iMPACT - Address 0x0002480B is not located at the start of a sector boundary. The whole sector will be erased. INFO:iMPACT - Address 0x0002480B is in sector 3. INFO:iMPACT - End block = 95 for address 0x0002480B. INFO:iMPACT - Address 0x00000000 is in sector 0. INFO:iMPACT - Address 0x0002480B is not located at the start of a sector boundary. The whole sector will be erased. INFO:iMPACT - Address 0x0002480B is in sector 3. INFO:iMPACT - Address 0x00000000 is in sector 0. INFO:iMPACT - Address 0x0002480B is not located at the start of a sector boundary. The whole sector will be erased. INFO:iMPACT - Address 0x0002480B is in sector 3. INFO:iMPACT - '1': Sector '0' is protected. INFO:iMPACT - '1': Sector '1' is protected. INFO:iMPACT - '1': Sector '2' is protected. INFO:iMPACT - '1': Sector '3' is protected. '1': Some sectors addressed by the configuration file are data protected. '1': One or more sectors used by the current configuration file is protected. Perform stand-alone erase operation to clear the protection. '1': Configuration data download to FPGA was not successful. DONE did not go high, please check your configuration setup and spi mode settings. PROGRESS_END - End Operation. Elapsed time = 20 sec. Request your response at the earliest. Regards, Salma --------------------------------------- This message was sent using the comp.arch.fpga web interface on http://www.FPGARelated.com |